Pomoc pri instalacii mikrotik

[jany+]

Takze ako idem na to ja detailne.
Vlozim do mechaniky CD po chvili vybehne ponuka, stlacim "a" zaskrtnu sa vsetky moznosti a potom stlacim "i" install
mikrotik sa nainstaluje a enterom dam reboot (CD s mechaniky vytiahnem)
Nabootju s HDD zadam admin, heslo prazdne a enter a som v konzole. Napisem setup a mam ponuku.
+ pred ponukou znamena, ze je to uz nakonfigurovane.
Potom musim este nastavit IP a gateway. Napisem 192.168.1.0/24
gateway prideli automaticky a rozsah pre DHCP tiez. Potom ma to pyta DNS, co mam zadat tam,
ved DNS mi prideluje ISP a nieje stale rovnaka.
V PC za routerom zadam do prehliadaca http://192.168.1.0, vyplnim login OK a som vo web rozhrani
idem na pppoe zapnem to a vyplnim meno a heslo a interface nastavim na ether2
idem na interface (mam tam 2x sietovka ether1 a ether2) ether1 je co ide s PC na ktorom je
mikrotik do switcha (zo switcha idu dalej ostatne PC v sieti) a ethernet2 je sietovka co ide
do HW routera ASUS (Asus je nastaveny v mode bridge) Na tej ether2 dam zapnut a vyberem moznost
aby IP priradilo automaticky (mal by pridelit ISP co je u mna T-Com) a nic sa nedeje, adresu neprideli
Co robim zle, alebo ako to mam nastavit, tu je schema ako to mam vsetko zapojene http://jany.ic.cz/schema2.jpg
tu je akysi vypis s konzoly


Trying 0.0.0.0...
Connected to 0.0.0.0.
Escape character is '^]'.

MikroTik v2.9.27
Login: admin
Password:

MMM MMM KKK TTTTTTTTTTT KKK
MMMM MMMM KKK TTTTTTTTTTT KKK
MMM MMMM MMM III KKK KKK RRRRRR OOOOOO TTT III KKK KKK
MMM MM MMM III KKKKK RRR RRR OOO OOO TTT III KKKKK
MMM MMM III KKK KKK RRRRRR OOO OOO TTT III KKK KKK
MMM MMM III KKK KKK RRR RRR OOOOOO TTT III KKK KKK

MikroTik RouterOS 2.9.27 (c) 1999-2006 www.routerclub.com


Terminal unknown detected, using single line input mode
[admin@MikroTik] > setup
Setup uses Safe Mode. It means that all changes that are made during setup
are reverted in case of error, or if Ctrl-C is used to abort setup. To keep
changes exit setup using the 'x' key.

[Safe Mode taken]
Choose options by pressing one of the letters in the left column, before
dash. Pressing 'x' will exit current menu, pressing Enter key will select the
entry that is marked by an '*'. You can abort setup at any time by pressing
Ctrl-C.
Entries marked by '+' are already configured.
Entries marked by '-' cannot be used yet.
Entries marked by 'X' cannot be used without installing additional packages.
r - reset all router configuration
+ l - load interface driver
+ a - configure ip address and gateway
+ d - setup dhcp client
* s - setup dhcp server
+ p - setup pppoe client
t - setup pptp client
x - exit menu
your choice [press Enter to setup dhcp server]: s
dhcp server interface: ether1
dhcp address space: 192.168.1.0/24
gateway for dhcp network: 192.168.1.254
addresses to give out: 192.168.1.1-192.168.1.253
dns servers:

[Fox!MURDER]

muzes nejak rozumne vysvetlit ten double post?

[jany+]

muzes nejak rozumne vysvetlit ten double post?

mozem.
Kedze som pouzil vyhladavanie a tam kde som to umiestnil prvi krat sa zacal trocha rozoberat mikrotik, tak som to umiestnil tam, ale po case som zistil, ze som asi v nespravnej sekcii, tak som to tam chcel zmazat, ale nenasiel som tam taku moznost (ziadny button a pod) preto to je 2x
Toto moze mod. alebo admin zmazat http://4um.overclocking.cz/showpost....7&postcount=21

[PavelN]

Mas tam nekolik chyb.
Prvni chyba je ze IP na LAN nemuze byt adresa site 192.168.1.0/24 ale napriklad 192.168.1.1/24.
Dalsi problem je ze pokud mas ADSL router v rezimu bridge tak na nem musis nastavit PPoE vcetne parametru co mas na pripojeni od tveho poskytovatele a ne jen DHCP klient, to nefunguje . Pro nastaveni je lepsi pouzivat winbox, je to lepsi nez nastavovani pres web.
Dalsi rady najdes na foru mikrotiku http://forum.routeros.cz

[jany+]

Mam Asus AM 602 a niesom si isty, ci tam pojde nastavit PPPoE pokial je to v bridge mode (skusim a dam vediet). Od poskytovatela mam len PPPoE parametre, co je meno a heslo, to je vsetko, IP a DNS mi prideli automaticky (tu DNS som uz na stranke t-comu nasiel, tak ju mozem zadat rucne). No a DHCP urcite na modeme nastavovat nebudem, ved sa to robi na mikrotiku. Na http://forum.routeros.cz niesu az taky ochotny ako vyzeraju

[jany+]

nieje mozne na modeme nastavit pppoe pokial je v bridge mode, to je jasne. A ked to nastavim priamo na mikrotiku tak t-com prideli IP aj gateway a to je vsetko, tam som skoncil....