[vyreseno] voodootv a polofunkcni zvuk

[Opty]

pokousim se zprovoznit zvuk na tv karte 3dfx voodootv fm... zvuk mi momentalne funguje pouze na prime

z tv karty vede kabel do cd in zvukove karty a podle me mam vse spravne nastavene (alsa, mixer, ...), protoze jinak by asi nesel zvuk ani na prime

pouzivam tvtime, zkousel jsem si i rucne vytvorit stationlist.xml pomoci udaju z obycejne tv, nepomohlo... zkousel jsem i xawtv a kdetv

podotykam, ze ve windows v dscaleru mi zvuk funguje skoro na vsech kanalech, i kdyz je pravda, ze to musim nastavit rucne, ale taky je tam mnohem vice moznosti

distribuce debian unstable, jadro 2.6.18

lspci -v | grep Bt
02:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
02:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)

dmesg | grep bttv
bttv: driver version 0.9.16 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 17) at 0000:02:0a.0, irq: 217, latency: 32, mmio: 0xf0000000
bttv0: detected: 3Dfx VoodooTV FM/ VoodooTV 200 [card=68], PCI subsystem ID is 121a:3000
bttv0: using: 3Dfx VoodooTV FM (Euro), VoodooTV 200 (USA) [card=68,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=008ff0a0 [init]
bttv0: Hauppauge/Voodoo msp34xx: reset line init [20]
bttv0: using tuner=33
bttv0: i2c: checking for MSP34xx @ 0x80... found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
bttv0: i2c: checking for TDA9887 @ 0x86... not found
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: registered device radio0
bttv0: PLL: 28636363 => 35468950 .. ok
bttv0: PLL can sleep, using XTAL (28636363).

dmesg | grep tuner
bttv0: using tuner=33
tuner 2-0060: Chip ID is not zero. It is not a TEA5767
tuner 2-0060: chip found @ 0xc0 (bt878 #0 [sw])
tuner 2-0060: microtune: companycode=4d54 part=04 rev=04
tuner 2-0060: microtune MT2032 found, OK

dmesg | grep msp
bttv0: Hauppauge/Voodoo msp34xx: reset line init [20]
msp3400 2-0040: MSP3450G-B6 found @ 0x80 (bt878 #0 [sw])
msp3400 2-0040: MSP3450G-B6 supports nicam and radio, mode is autodetect and autoselect

pokud ma nekdo nejaky napad, co je spatne a jak to rozchodit, tak mu budu neskonale vdecen...

(btw proc je na konci kodu tak siroka mezera?)

[Opty]

modprobe msp3400 opmode=0 a uz to funguje