SpeedFan 4.2x

[meteor]

Zkoušeli jste někdo SMART v tom posledním SpeedFanu? Se mi zdá, že se mi nějak výrazně (tak o 8 až 10%) zlepšil výsledek mojeho starého 200GB Maxtora DM10
Nepozorovali jste něco podobného?

[Darth Maul]

Zkoušeli jste někdo SMART v tom posledním SpeedFanu? Se mi zdá, že se mi nějak výrazně (tak o 8 až 10%) zlepšil výsledek mojeho starého 200GB Maxtora DM10
Nepozorovali jste něco podobného?

Zkoušel jsem teď zrovna disk, který prodávám, a rozdíl mezi 4.33 a 4.34 není naprosto žádný...

[meteor]

Zkoušel jsem teď zrovna disk, který prodávám, a rozdíl mezi 4.33 a 4.34 není naprosto žádný...

No jo, ale ty neprodáváš žádného staříčka
U mých dvou zbývajících (Samsung 500GB a WD Raptor 74GB) jsou výsledky úplně stejné... ale co, možná je to jenom haluz. Třeba ještě někdo přispěje, heh.

[rombo]

No jo, ale ty neprodáváš žádného staříčka
U mých dvou zbývajících (Samsung 500GB a WD Raptor 74GB) jsou výsledky úplně stejné... ale co, možná je to jenom haluz. Třeba ještě někdo přispěje, heh.

tak ja mam na Samsungu 400GB taky uplne stejny teploty.. takze to mozna byla jenom haluz

[AjsTi]

Download

 - released to the public the EXOTICS tab 
 - fixed 120 DPI issue in CONFIGURE dialog 
 - added full support for Areca RAID controllers 
 - greatly improved SCSI support 
 - added support for Abit uGuru 3 (uGuru 2005) 
 - added full support for Intel FB-DIMM temperature readings 
 - added full support for ITE IT8720F 
 - added full support for Andigilog aSC7611 
 - added full support for LM96000 (it was previously detected as LM85B) 
 - added full support for Analog Devices ADT7490 
 - added full support for SMSC SCH5327 
 - fixed Windbond W83766HG hardware monitor detection on some Asus motherboards 
 - improved CPU identification routines 
 - added support for a new revision of the WINBOND W83637HF 
 - added support for WINBOND W83637HF at unusual addresses 
 - added support for Asus F8000 at unusual addresses 
 - added identification of the SMSC SCH5514 
 - added identification of SMSC EMC2300 
 - added ITE IT8718F fifth fan speed reporting 
 - added identification of Analog Devices ADP3228 
 - added identification of ITE IT8512F 
 - added identification of Winbond W83667HG SuperIO chip 
 - identified a new revision of Fintek F71872 hardware monitor subsystem 
 - added preliminary detection of the HECI driver 
 - fixed a bug in SMSC LPC47M172 support code that prevented fan speeds to be properly reported 
 - 45nm Intel CPUs with CPUID=0x10676 now use a Tjmax value of either 105C or 90C 
 - added full support for nVidia MCP65 SMBus 
 - added full support for nVidia MCP67 SMBus 
 - added full support for nVidia MCP73 SMBus 
 - added full support for nVidia MCP78S SMBus 
 - added full support for VIA CX700M SMBus 
 - added full support for Intel 82801JIB SMBus 
 - fixed an issue where the Intel SMBus couldn't be accessed and messages like SMBus msg : SMB Error $14 : FAILED (50) were generated 
 - enabled Intel ICH8M-E SMBus device, if needed 
 - enabled 631xESB SMBus, if needed 
 - enabled SMBus on Intel ICH9R, if needed 
 - preliminary detection of AMD CD5536 SMBus 
 - some SMBus addresses on Asus Striker Extreme are no longer scanned 
 - SMBus is no longer scanned at address $2E on DELL XPS710 
 - Tyan S2927 second SMBus is no longer scanned 
 - some addresses on the SMBus of Asus P5NT WS are no longer scanned 
 - some addresses on the SMBus of the Intel DX38BT are no longer scanned 
 - some SMBus addresses are no longer scanned on Asus M2N32-SLI DELUXE 
 - the second nForce SMBus is no longer scanned on FIC AU31 
 - some addresses on the SMBus of Supermicro H8DCE are no longer scanned 
 - added some SMBus scan exclusions for Intel D5400XS 
 - added /NOGIVEIO command line parameter to disable access to giveio.sys 
 - added /NOGEFORCEROM command line switch that will prevent SpeedFan from reading nVidia GeForce ROMs (useful if it takes too much time) 
 - nVidia video BIOS is now stored in a file for later retrieval 
 - fixed an access violation under Win9x with some nVidia video cards 
 - battery status messages are no longer displayed 
 - upon resume, all controlled fans are set to 100% for half a second, then set to their minimum fan speed 
 - added new configuration option SHOWSTATICICON 
 - enabled Intel 6300ESB SMBus if needed

[M@to]

Download

- greatly improved temperature reporting for almost all nVidia video cards
- now fan speeds are lowered more aggressively
- added support for AMD K11 temperature sensor
- added full support for SMSC EMC6W201
- added full support for SMSC SCH5127
- added support for SMSC EMC2710P fan speed readings
- ARECA RAID support updated to Build 270
- added AMCC/3ware test code
- improved IT8720F identification
- fixed F1 context sensitive help key support
- better identification of DIRECT RAMBUS modules
- enabled Intel ICH8 SMBus, if needed
- identified SMSC SCH5317
- some addresses on the Asus P5N32-E SLI are no longer scanned
- some addresses on the Asus Rampage Formula are no longer scanned
- some addresses on EVGA NFORCE 680i LT SLI are no longer scanned

[Firuz]

Asi jste nikdo nezjistil, jak Speedfan nastavit, aby se po spuštění automaticky načetly nastavené manuální hodnoty otáček větráku, že? Tato věc mi v něm dost chybí