ATI Tray Tool v.1.0.0.195 - 1.0.3.780 NEW

[Spajdr]

celá zpráva

1.2.6.940
[F] Fixed bug when manual fan control can not be applied[*] Updated some translation files
[F] Fixed Old I2C Method to be compatible with X1xxx boards in memory voltage control procedure
[+] Added ability to change how ATT will react on "ATI HotKey poller" service. (in General options)[*] Updated Overdrive control procedure. Now you can set any available clocks for OverDrive even beyond the Catalyst limits!
And change GPU Voltage too.
[+] Added option to apply OverDrive settings on startup
[+] Added Portuguese (Brazilian) and Belorussian translations
________
Can be downloaded from Guru3d (when will be updated) or by checking for new version in General options in ATI Tray Tools.

[Spajdr]

Ray jede

News about next release
At this moment I'm finishing adding new method of overclocking for R5xx boards. This method will be called "Driver Level".
What will do this method:
1. Overclocking will be done by Catalyst itself like Overdrive
2. Voltage will be applied by driver for GPU and by ATT for memory
3. ATT will emulate Overdrive job, but will allow to set clocks when you want it instead of when you run full screen 3D application.
4. This should work even if you didn't disable ATI HotKey poller! And clocks will not resets by that service in 3D games
5. With this method clocks will not resets when you play any video files (checked on my 1800XT, no more resets)
6. More stable overclocking. Catalyst know HOW to do overclock job better that any other utils
________
I hope this method will work without problems, but there are some disadvantages:
1. It seems that this method can be used only on video boards with Overdrive support (I will check it with non Overdrive board 1600Pro)
2. The step in MHz will be higher than in Low Level ( about 6MHz)

[Spajdr]

celkem zajímavé reakce od Unwindera a Wizzard na práci Raye
http://www.rage3d.com/board/showthread.php?t=33868890

[AXB]

celkem zajímavé reakce od Unwindera a Wizzard na práci Raye
http://www.rage3d.com/board/showthread.php?t=33868890

No teda jestli je to pravda, tak to celkem mení můj názor na Mr. Adamse... ale ne na ATT.

[Haste]

Jediny problem, proc jeste pouzivam AT a ne ATT je ten, ze ma dost divne nastaveni voltazi u pameti. Mel by jeste dodelat moznost nastaveni vsech 3 voltazi na pameti a jeste aby se to nastaveni aplikovalo pri prepnuti do 3D. Pak jeste nejak obejit relaxovane casovani pameti, protoze to silene zpomaluje oproti AT (par tisic v AQM3) a pak by to bylo super )

[AXB]

ATI Tray Tools 1.2.6.955

[+] Added new overclocking method for X1xxx boards with Overdrive support. "Driver Level overclocking".
Near the same method first was introduced in RivaTuner and then in ATITool.
What will do this method?
1. Overclocking will be done by Catalyst itself like Overdrive
2. Voltage will be applied by driver for GPU and by ATT for memory. Only for hardware with voltage regulator
3. ATT will emulate Overdrive job, but will allow to set clocks when you want it instead of when you run full screen 3D application.
4. This should work even if you didn't disable ATI HotKey poller! And clocks will not reset by that service in 3D games
5. With this method clocks shouldn't not resets when you play any video files (tested on my 1800XT)
6. More stable overclocking.
7. You can create full featured overclocking profiles in ATT and use them in game profiles.
8. For Video board without OverDrive support ATT will use alternative method for overclocking like used in ATI WinClk and also in last release of RivaTuner.
But this method has some disadvantages:
1. Big steps for clock regulators. For GPU about 6Mhz and about 9Mhz for Memory.
2. Not all voltages can be applied. Try not to set voltage less than 1.1000 and voltage can not be applied if video doesn't support voltage control.
[*] Improved Overdrive 3 support. Now ATT will calculate nearest possible clocks before applying.
[+] Added Japenese, Finnish translations
[+] Added option to include clocks in Overclocking Profile. Now you can create profile just for FAN or for Voltage control without GPU and Memory clocks. "C" means that profile has Clocks included.
[*] Updated user interface in some dialog windows.
[*] Updated "New AA & AF Methods" database. Added a lot of experimental options to improve antialiasing methods like SAAOM, EATM.

[pulec7]

No ja bych potreboval poradit s voltazi pameti. Me de nastavovat pouze jadro, kdyz zmenim vurent voltaze pameti tak to je dle me jen tak kdyz to jede ve 2d a jeste mi nejde prepsat po pouziti se mi vraci zpet na svoji hodnotu.