co treba tohle ?

Kód:
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   117   117   021    Pre-fail  Always       -       4675
  4 Start_Stop_Count        0x0032   100   100   040    Old_age   Always       -       338
  5 Reallocated_Sector_Ct   0x0033   199   199   140    Pre-fail  Always       -       1
  7 Seek_Error_Rate         0x000b   200   200   051    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   073   073   000    Old_age   Always       -       20233
 10 Spin_Retry_Count        0x0013   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0013   100   100   051    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       177
194 Temperature_Celsius     0x0022   111   253   000    Old_age   Always       -       39
196 Reallocated_Event_Count 0x0032   199   199   000    Old_age   Always       -       1
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0012   200   200   000    Old_age   Always       -       1
199 UDMA_CRC_Error_Count    0x000a   200   253   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0009   200   155   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 08 00 00  46d+00:46:50.108  NOP [Abort queued commands]
  16 00 30 00 00 98 94 00  46d+00:46:50.108  RECALIBRATE [RET-4]
  00 00 25 00 00 08 00 00  46d+00:46:50.108  NOP [Abort queued commands]
  16 00 30 00 00 88 94 00  46d+00:46:50.108  RECALIBRATE [RET-4]
  00 00 35 00 00 48 00 00  46d+00:46:50.108  NOP [Abort queued commands]

Error 9 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  16 00 30 00 00 88 95 00  46d+00:46:48.358  RECALIBRATE [RET-4]
  00 00 25 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  00 00 35 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  16 00 a7 00 00 20 53 00  46d+00:46:48.358  RECALIBRATE [RET-4]

Error 8 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 f0 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 f0 00 00  46d+00:46:46.558  NOP [Abort queued commands]
  00 00 25 00 00 00 01 00  46d+00:46:46.558  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:46.558  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:46.558  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:46.558  RECALIBRATE [RET-4]

Error 7 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 f8 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 f8 00 00  46d+00:46:44.808  NOP [Abort queued commands]
  00 00 25 00 00 00 01 00  46d+00:46:44.808  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:44.808  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:44.808  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:44.808  RECALIBRATE [RET-4]

Error 6 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:43.058  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:43.058  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%       572         372282527
# 2  Short offline       Completed: read failure       90%       572         372282527
# 3  Conveyance offline  Completed without error       00%       711         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.