[HW] Slack - hda lost interrupt

[Rainbow]

No zjavne je problem s prenosom dat cez kabel - otazka je, ci je zly disk alebo nie...
btw. pouzivaj [code], prvy post som ti upravil do citatelnej podoby

[Lukas L.]

nj - jsem si zvyknul na tlacitka phpBB... takze upraveno

kabel jsem uz menil..disk snad spatny neni...zkousel jsem googlit(pfff http://www.sysopt.com/forum/archive/...p/t-57098.html -

Point being this: The ALi "1543" south bridge contains an ALi "5229" IDE controller unit, rev. 20h or 32 decimal, that was designed to be UDMA33 capable, but was MUCH later found to cause all kinds of problems at that speed. I have one of those too, on an earlier board using the Aladdin IV north.

), zda Ali IV IDE nema problem s DMA...ono tedy spis se zda, ze cela ta deska je jeden problem...ale do doby nez sezenu napr. nejakou i430TX MB bych to potreboval nejak upravit/opravit
podle bios stringu by to mel byt Biostar M5ATA

stejne myslim, ze tyhle desky nejsou vubec staveny na 24/7 provoz...zvlaste kdyz od toho clovek chce nejake intenizvnejsi I/O operace ...

[Rainbow]

Ano, M1543 ma vselijake problemy, ale driver v Linuxe by to mal mat vsetko osetrene.
Naozaj si najprv over, ci to robi/nerobi ten disk, kym budes menit dosku...

[Airwolf]

co treba tohle ?

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   200   200   051    Pre-fail  Always       -       0
  3 Spin_Up_Time            0x0007   117   117   021    Pre-fail  Always       -       4675
  4 Start_Stop_Count        0x0032   100   100   040    Old_age   Always       -       338
  5 Reallocated_Sector_Ct   0x0033   199   199   140    Pre-fail  Always       -       1
  7 Seek_Error_Rate         0x000b   200   200   051    Pre-fail  Always       -       0
  9 Power_On_Hours          0x0032   073   073   000    Old_age   Always       -       20233
 10 Spin_Retry_Count        0x0013   100   100   051    Pre-fail  Always       -       0
 11 Calibration_Retry_Count 0x0013   100   100   051    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       177
194 Temperature_Celsius     0x0022   111   253   000    Old_age   Always       -       39
196 Reallocated_Event_Count 0x0032   199   199   000    Old_age   Always       -       1
197 Current_Pending_Sector  0x0012   200   200   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0012   200   200   000    Old_age   Always       -       1
199 UDMA_CRC_Error_Count    0x000a   200   253   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0009   200   155   051    Pre-fail  Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 10 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 08 00 00  46d+00:46:50.108  NOP [Abort queued commands]
  16 00 30 00 00 98 94 00  46d+00:46:50.108  RECALIBRATE [RET-4]
  00 00 25 00 00 08 00 00  46d+00:46:50.108  NOP [Abort queued commands]
  16 00 30 00 00 88 94 00  46d+00:46:50.108  RECALIBRATE [RET-4]
  00 00 35 00 00 48 00 00  46d+00:46:50.108  NOP [Abort queued commands]

Error 9 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 08 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  16 00 30 00 00 88 95 00  46d+00:46:48.358  RECALIBRATE [RET-4]
  00 00 25 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  00 00 35 00 00 08 00 00  46d+00:46:48.358  NOP [Abort queued commands]
  16 00 a7 00 00 20 53 00  46d+00:46:48.358  RECALIBRATE [RET-4]

Error 8 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 f0 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 f0 00 00  46d+00:46:46.558  NOP [Abort queued commands]
  00 00 25 00 00 00 01 00  46d+00:46:46.558  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:46.558  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:46.558  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:46.558  RECALIBRATE [RET-4]

Error 7 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 f8 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 f8 00 00  46d+00:46:44.808  NOP [Abort queued commands]
  00 00 25 00 00 00 01 00  46d+00:46:44.808  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:44.808  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:44.808  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:44.808  RECALIBRATE [RET-4]

Error 6 occurred at disk power-on lifetime: 571 hours (23 days + 19 hours)
  When the command that caused the error occurred, the device was doing SMART Offline or Self-test.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 9f 94 30 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]
  16 00 30 00 00 88 92 00  46d+00:46:43.058  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]
  16 00 30 00 00 88 8f 00  46d+00:46:43.058  RECALIBRATE [RET-4]
  00 00 25 00 00 00 01 00  46d+00:46:43.058  NOP [Abort queued commands]

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed: read failure       90%       572         372282527
# 2  Short offline       Completed: read failure       90%       572         372282527
# 3  Conveyance offline  Completed without error       00%       711         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.