[HW] Slack - hda lost interrupt

[Lukas L.]

posledni dobou mam cim dal tim vetsi problem s hda

lspci -v

00:00.0 Host bridge: ALi Corporation M1531 [Aladdin IV] (rev b3)
        Subsystem: ALi Corporation M1531 [Aladdin IV]
        Flags: bus master, slow devsel, latency 32

00:02.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (rev b4)
        Flags: bus master, medium devsel, latency 0

00:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Edimax Computer Co. EN-9130TX
        Flags: bus master, medium devsel, latency 64, IRQ 11
        I/O ports at 6400 [size=256]
        Memory at e0000000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

00:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Compex FN22-3(A) LinxPRO Ethernet Adapter
        Flags: bus master, medium devsel, latency 64, IRQ 10
        I/O ports at 6500 [size=256]
        Memory at e0001000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

00:0b.0 IDE interface: ALi Corporation M5229 IDE (rev 20) (prog-if fa)
        Flags: bus master, medium devsel, latency 64, IRQ 10
        I/O ports at f000 [size=16]

hdparm -i /dev/hda

/dev/hda:

 Model=ST34311A, FwRev=8.01, SerialNo=5BF2A168
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=8944/15/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=256kB, MaxMultSect=16, MultSect=off
 CurCHS=8944/15/63, CurSects=8452080, LBA=yes, LBAsects=8452080
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 *mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: device does not report version:  1 2 3 4

dmesg

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0b.0
PCI: Assigned IRQ 10 for device 00:0b.0
ALI15X3: chipset revision 32
ALI15X3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: ST34311A, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 8452080 sectors (4327 MB) w/256KiB Cache, CHS=526/255/63
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: hda1 hda2 hda3

v lilo.conf mam

image = /boot/vmlinuz-2.4.29
  root = /dev/hda1
  label = Linux-2-4-29
  append = "ide=nodma"
  read-only

zkousel jsem i hdparm -d0 /dev/hda, v BIOSu ruzne povypinat DMA a zapnout PIO vymenit kabel,...

syslog mam plny hlasek jako :

Aug  2 04:52:02 gw1 kernel: hda: lost interrupt
Aug  2 04:59:54 gw1 kernel: hda: lost interrupt
Aug  2 05:11:52 gw1 kernel: hda: lost interrupt
Aug  2 05:13:48 gw1 kernel: hda: lost interrupt

Aug  2 13:12:12 gw1 kernel: hda: lost interrupt
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 13:12:12 gw1 kernel: hda: status timeout: status=0xd0 { Busy }
Aug  2 13:12:12 gw1 kernel: hda: no DRQ after issuing WRITE
Aug  2 13:20:14 gw1 kernel: hda: lost interrupt
Aug  2 13:32:07 gw1 smartd[144]: Device: /dev/hda, ATA error count increased from 41 to 43
Aug  2 13:50:12 gw1 kernel: hda: lost interrupt


Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: ide0: reset: success
Aug  2 15:48:39 gw1 smartd[144]: Device: /dev/hda, ATA error count increased from 43 to 47

co je to presne za MB nevim (maximalne zjistit pres BIOS string) - P55C 200, 3C509 ISA , 2x Realtek 8139 PCI, 1x ATAPI CDROM, 1x HDD ST34311A - kazdy na svem IDE kanale, 2x DIMM celkove 128MB

je to zapnuty 24/7 (router, DNS, DHCP, mail+anti spam,www, ...) - jen nevim jestli je to HW problem nebo jestli je moznost to spravit novejsim jadrem....