[HW] Slack - hda lost interrupt

[Lukas L.]

posledni dobou mam cim dal tim vetsi problem s hda

lspci -v

00:00.0 Host bridge: ALi Corporation M1531 [Aladdin IV] (rev b3)
        Subsystem: ALi Corporation M1531 [Aladdin IV]
        Flags: bus master, slow devsel, latency 32

00:02.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV] (rev b4)
        Flags: bus master, medium devsel, latency 0

00:03.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Edimax Computer Co. EN-9130TX
        Flags: bus master, medium devsel, latency 64, IRQ 11
        I/O ports at 6400 [size=256]
        Memory at e0000000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

00:05.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
        Subsystem: Compex FN22-3(A) LinxPRO Ethernet Adapter
        Flags: bus master, medium devsel, latency 64, IRQ 10
        I/O ports at 6500 [size=256]
        Memory at e0001000 (32-bit, non-prefetchable) [size=256]
        Capabilities: [50] Power Management version 2

00:0b.0 IDE interface: ALi Corporation M5229 IDE (rev 20) (prog-if fa)
        Flags: bus master, medium devsel, latency 64, IRQ 10
        I/O ports at f000 [size=16]

hdparm -i /dev/hda

/dev/hda:

 Model=ST34311A, FwRev=8.01, SerialNo=5BF2A168
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=8944/15/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=256kB, MaxMultSect=16, MultSect=off
 CurCHS=8944/15/63, CurSects=8452080, LBA=yes, LBAsects=8452080
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 *mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: device does not report version:  1 2 3 4

dmesg

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0b.0
PCI: Assigned IRQ 10 for device 00:0b.0
ALI15X3: chipset revision 32
ALI15X3: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
hda: ST34311A, ATA DISK drive
hdc: CD-540E, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 8452080 sectors (4327 MB) w/256KiB Cache, CHS=526/255/63
hdc: attached ide-cdrom driver.
hdc: ATAPI 40X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
Partition check:
 hda: hda1 hda2 hda3

v lilo.conf mam

image = /boot/vmlinuz-2.4.29
  root = /dev/hda1
  label = Linux-2-4-29
  append = "ide=nodma"
  read-only

zkousel jsem i hdparm -d0 /dev/hda, v BIOSu ruzne povypinat DMA a zapnout PIO vymenit kabel,...

syslog mam plny hlasek jako :

Aug  2 04:52:02 gw1 kernel: hda: lost interrupt
Aug  2 04:59:54 gw1 kernel: hda: lost interrupt
Aug  2 05:11:52 gw1 kernel: hda: lost interrupt
Aug  2 05:13:48 gw1 kernel: hda: lost interrupt

Aug  2 13:12:12 gw1 kernel: hda: lost interrupt
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 13:12:12 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 13:12:12 gw1 kernel: hda: status timeout: status=0xd0 { Busy }
Aug  2 13:12:12 gw1 kernel: hda: no DRQ after issuing WRITE
Aug  2 13:20:14 gw1 kernel: hda: lost interrupt
Aug  2 13:32:07 gw1 smartd[144]: Device: /dev/hda, ATA error count increased from 41 to 43
Aug  2 13:50:12 gw1 kernel: hda: lost interrupt


Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: status=0x51 { DriveReady SeekComplete Error }
Aug  2 15:21:48 gw1 kernel: hda: multwrite_intr: error=0x00 { }
Aug  2 15:21:48 gw1 kernel: ide0: reset: success
Aug  2 15:48:39 gw1 smartd[144]: Device: /dev/hda, ATA error count increased from 43 to 47

co je to presne za MB nevim (maximalne zjistit pres BIOS string) - P55C 200, 3C509 ISA , 2x Realtek 8139 PCI, 1x ATAPI CDROM, 1x HDD ST34311A - kazdy na svem IDE kanale, 2x DIMM celkove 128MB

je to zapnuty 24/7 (router, DNS, DHCP, mail+anti spam,www, ...) - jen nevim jestli je to HW problem nebo jestli je moznost to spravit novejsim jadrem....

[Rainbow]

Skus, ci to robi aj s inym diskom.

[David Jaša]

Aug 2 15:48:39 gw1 smartd[144]: Device: /dev/hda, ATA error count increased from 43 to 47

pošli sem ještě výpis

smarctl -a /dev/hda

zkousel jsem i ..., v BIOSu ruzne povypinat DMA a zapnout PIO ...

To v linuxu nemá moc smysl, ten jakmile čapne řadič disků do svých spárů, tak na bios zvysoka s*e. Příkladem budiž bezproblémové provozování různých velkých disků (co zvládne řadič, tj. LBA32) na deskách pro pentium. PIO a DMA má cenu nastavovat jenom přes hdparm.

[Rainbow]

PIO a DMA má cenu nastavovat jenom přes hdparm.

Nie je to uplne pravda - na 1 serveri som sa divil ze preco ide disk len v UDMA33 - myslel som, ze tam niekto dal 40-zilovy kabel. Ked som tam isiel osobne, tak som pozrel do BIOSu a tam bolo DMA uplne vypnute. Takze Linux nastavil aspon UDMA33, ale viac uz nezvladol. Po zapnuti v BIOSe funguje aj UDMA100.

[David Jaša]

2Rainbow: Je možný, že přepnutí do "PIO" módu znamenalo nějaký safe/legacy mód. IMHO potom by k tomu to UDMA2 (ATA33) sedělo.

[Lukas L.]

no SMART rve jak o zivot - mam z smartd udelany mail info :

The following warning/error was logged by the smartd daemon:

Device: /dev/hda, ATA error count increased from 52 to 54

For details see host's SYSLOG (default: /var/log/messages).

smartctl -a /dev/hda

smartctl version 5.36 [i486-slackware-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Model Family:     Seagate U4 family
Device Model:     ST34311A
Serial Number:    5BF2A168
Firmware Version: 8.01
User Capacity:    4 327 464 960 bytes
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   4
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Wed Aug  2 22:34:17 2006 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (3120) seconds.
Offline data collection
capabilities:                    (0x1b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        No Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        No General Purpose Logging support.
Short self-test routine
recommended polling time:        (   2) minutes.
Extended self-test routine
recommended polling time:        (  10) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x0008   111   099   000    Old_age   Offline      -       33216423
  3 Spin_Up_Time            0x0006   097   097   000    Old_age   Always       -       0
  4 Start_Stop_Count        0x0013   100   100   020    Pre-fail  Always       -       90
  5 Reallocated_Sector_Ct   0x0013   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x0009   075   060   030    Pre-fail  Offline      -       4335450923
 10 Spin_Retry_Count        0x0013   100   100   090    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0013   099   099   020    Pre-fail  Always       -       1368
197 Current_Pending_Sector  0x0010   100   100   000    Old_age   Offline      -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 54 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 54 occurred at disk power-on lifetime: 9572 hours (398 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 28 5f 0f 0c e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 53 occurred at disk power-on lifetime: 9572 hours (398 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 30 00 45 3c e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 52 occurred at disk power-on lifetime: 9572 hours (398 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 80 00 c1 00 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 51 occurred at disk power-on lifetime: 9572 hours (398 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 80 80 86 00 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

Error 50 occurred at disk power-on lifetime: 9572 hours (398 days + 20 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  01 51 80 00 8b 00 e0  Error:

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Device does not support Selective Self Tests/Logging

jinak uz jsem na tom routeru provozoval vic disku a i MB - bohuzel si nepamatuju vsechny modely - vetsi problemy mam az s timhle

Kernel 2.4.29, MB string 05/27/98-Ali-154x-2a5kib09c-00

[Airwolf]

pokud to pribyva neriskuj. ja takhle menim disky rovnou na linuxovych serverech. temhle diskum sverim maximalne cachovani dat...