ATITool Releases

[Crusheer]

ATITool 0.25 beta 11
RELEASE NOTES
- Fixed Shared Memory
- Fixed "Minimum Step" displaying random number on X1000 Series
- Fixed a few "Mhz" / "MHz" typos
- Added a 250 ms delay when loading a profile between setting voltage and setting clocks
- Fixed the lost manifest for XP Visual Styles
- ATITool will disable 2D/3D switch on X1800XT now
- Memory OC disabled for X1300, it doesn't work yet

DOWNLOAD: Techpowerup

[Crusheer]

W1zzard na foru TechPowerUp rekl release notes k zatim nevydane bete 12.


- Added support for R580
- Added voltage change support for VDDCI on R580
- Fixed Adaptive AA checkbox enabled on NVIDIA
- Improved detection for "2D/3D switch enabled"
- Some debugging output removed
- Fixed negative ranges for temp. monitoring graph
- Added Yes/No question to disable 3D switch dialog
- More fixes to hotkey code

[.:::iGor:::.]

ATITool 0.25 Beta 12

- Added support for X1900 Series
- Added voltage change support for VDDCI on R580
- Fixed Adaptive AA checkbox enabled on NVIDIA
- Improved detection for "2D/3D switch enabled"
- Some debugging output removed
- Fixed negative ranges for temp. monitoring graph
- Added Yes/No question to disable 3D switch dialog
- More fixes to hotkey code
- Shift key is no longer required to display the fuses info
- Added longer delay after voltage change from profile, also put clock change as last change

http://www.techpowerup.com/downloads/get.php?id=220

[.:::iGor:::.]

ATITool 0.25 Beta 13

- Logo changed
- Fixed problem with 3D clock change messagebox incorrectly saving answer state
- Changed voltage behaviour when switching profiles
- Fixed crash issue when switching profiles under high 3D load
- Added Driver Tweaks: Temporal AA, Level of Detail, Adaptive AA, Geometry - Instancing, Catalyst AI.
- Fixed issue with incorrectly saved gamma
- Fixed VDCCI no getting saved to profile

http://www.techpowerup.com/downloads/235

[Spajdr]

beta 14 is out now..

- Fixed crash on X1900 when entering settings under high 3D load
- Show messagebox with explanation and link when user clicks on dump bios button on x1000
- Disabled saving stuff to default profile for Gamma, Mem, Fan. Default profile is default and not a custom setup
- Added support for many ATIGL GPUs
- Fixed "do you want to disable ati clock service" warning not saving "do not ask me again"
- Added Gamma for X1000 Series
- Changed rendering so that there is no more lag when not scanning. during scans this might still be possible, to maximize heat output
- Fixed issue where the renderer would not initialize properly if running on secondary adapter
- Bug where ATITool was never picking up artifacts fixed

http://www.techpowerup.com/downloads/259

[Crusheer]

nevíte někdo kdy bude nová verze? normálně vycházely tak po dvou týdnech, teď je tu beta 14 nejnovější už asi 3 měsíce...

[MisoSK]

mam catalyst 6.8 na 1800gto a ta beta 16 mi roby artefakty aj pri zakladnych taktoch, ale v hrach som nic nepostrehol.

[Haste]

mam catalyst 6.8 na 1800gto a ta beta 16 mi roby artefakty aj pri zakladnych taktoch, ale v hrach som nic nepostrehol.

No je to stale horsi. W1zzard uz je z toho pomerne nestastny, protoze ATi udelala OCing X1k rady vskutku nechutne spatne diky te jejich debilni HPooler sluzbe. Holt si bud pockame, nez neco vymysli, ale jestli chces stabilni OC na X1k rade, tak musis zustat u Cat. 6.3 a starsi verze AT.

[Haste]

Ted se to rozjelo. Mame tu ATiTool PreBeta 16 R4

Wizzard notes:
"please install this
make sure ati services are running,
set switch to 3d on atitool start,
set the ati2evxx.exe handling to not affected,
reboot to be safe,
test if video clock switches are happening,
now launch atitool and close it again,
check if the video clock switches are gone now,
so should any other clock switches from ati driver."

[BRABUS]

tak proto mi nejde pretaktovat grafarna.Jadro maximalne na 648 a pameti me nepusti ATItool vubec.mam cc6.8.Kdyz to pretaknu tak 3DMark05 mi hodi asi o 500bodu min jak default

[Spajdr]

no ta beta4 je úplně o ničem.