Dualne pripojenie LAN

[steelman]

Ahojte,

Momentalne sedim u klienta v sofii a potreboval by som vediet ci je mozne nejako na mojom firemnom notebooku s winxp nastavit nejake routovanie sieti na 2 rozne sietovky.

Aby som vysvetlil. Na net sa pripajam cez wifi ale akonahle potrebujem ist robit nieco do databazy u klienta musim pripojit lan kabel a samozrejme potom mi nejde net. Tym padom ak sa potrebujem o niecom poradit s kolegmi alebo sharnut desktop tak nemozem a musim sa odpojit z kabla a zapnut wifi ...

Potreboval by som aby vsetko z ip 10.* islo na lan kabel a vsetko ostatne na wifi

Ak viete o nejakom sposobe budem rad ked mi poskytnete step by step navod

Diky.

[Petrik]

Zakaz DHCP (automaticke) nastaveni LAN sitovky, dej tam rucne nejakou volnou IP adresu z rozsahu te LAN a je to. Pravdepodobne by take fungovalo nejdrive pripojit LAN a az po tom ten tvuj jinej net.

[Jezevec]

On bude spis problem v tom, ze kdyz pripoji LAN tak se odpoji WiFi. Jinak se to dela pomoci route add ...

Jop a pokud na wifi je jinej rozsah nez na LAN, funguje to od prirody, kdyz je stejnej, tak to fungovat nebude nikdy.

[steelman]

Je to tak ako pise jezevec. Po pripojeni kabla ma odpoji z wifiny.
Ak to pomoze tak pridavam vypis z ipconfig a route:

ipconfig:

Ethernet adapter Wireless Network Connection:

        Connection-specific DNS Suffix  . : xx.xx.bg
        IP Address. . . . . . . . . . . . : 192.168.60.73
        Subnet Mask . . . . . . . . . . . : 255.255.254.0
        Default Gateway . . . . . . . . . : 192.168.60.1

Ethernet adapter Local Area Connection:

        Connection-specific DNS Suffix  . : xx.xx.bg
        IP Address. . . . . . . . . . . . : 10.10.9.19
        Subnet Mask . . . . . . . . . . . : 255.255.254.0
        Default Gateway . . . . . . . . . : 10.10.8.1

route:

===========================================================================
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 1b 77 16 3e 57 ...... Intel(R) PRO/Wireless 3945ABG Network Connection
 - Packet Scheduler Miniport
0x3 ...00 16 d4 f3 ef 9d ...... Broadcom NetXtreme Gigabit Ethernet - Packet Sch
eduler Miniport
0x4 ...44 45 53 54 42 00 ...... Nortel IPSECSHM Adapter - Packet Scheduler Minip
ort
0x10006 ...00 ff d8 e8 a8 89 ...... Juniper Network Connect Virtual Adapter
===========================================================================
===========================================================================
Active Routes:
Network Destination        Netmask          Gateway       Interface  Metric
          0.0.0.0          0.0.0.0        10.10.8.1      10.10.9.19       20
          0.0.0.0          0.0.0.0     192.168.60.1   192.168.60.73       25
        10.10.8.0    255.255.254.0       10.10.9.19      10.10.9.19       20
       10.10.9.19  255.255.255.255        127.0.0.1       127.0.0.1       20
   10.255.255.255  255.255.255.255       10.10.9.19      10.10.9.19       20
        127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1       1
     192.168.60.0    255.255.254.0    192.168.60.73   192.168.60.73       25
    192.168.60.73  255.255.255.255        127.0.0.1       127.0.0.1       25
   192.168.60.255  255.255.255.255    192.168.60.73   192.168.60.73       25
        224.0.0.0        240.0.0.0       10.10.9.19      10.10.9.19       20
        224.0.0.0        240.0.0.0    192.168.60.73   192.168.60.73       25
  255.255.255.255  255.255.255.255       10.10.9.19      10.10.9.19       1
  255.255.255.255  255.255.255.255       10.10.9.19               4       1
  255.255.255.255  255.255.255.255       10.10.9.19           10006       1
  255.255.255.255  255.255.255.255    192.168.60.73   192.168.60.73       1
Default Gateway:         10.10.8.1
===========================================================================
Persistent Routes:
  None

Staticku IP samozrejme nemozem nastavit.

[Petrik]

Co znamena vyraz "odpoji od wifiny"? Jakoze spadne link? Tomu neverim, tohle snad ani wokna neumi... moje zkusenost je takova, ze kdyz pripojim wokna treba k deseti sitim, tak vsechny jedou, akorat default GW si vezme z te posledne pripojene. Lokani IP rozsahy ale fungovat musi, leda by se prekryvaly, coz neni tento pripad. Proc nemuzes nastavit statickou IP? aha, ted koukam ze tobe zustaly dve default GW...tak proste musis tu z LAN zakazat, zkusil bych ji vymazat (prikaz route), nebo proste nastavit statickou IP. Jediny duvod, proc by neslo nastavit statickou IP je, ze by switch filtroval MAC z jinych nez povolenych IP adres pres ARP a DHCP.

[monsoon]

Proc to delat slozite, kdyz to jde naprosto jednoduse, presne tak jak jiz psal Jezevec ve svem postu.

1) Je potreba zmenit metriku interfacu, aby wifi mela metriku nizsi nez lan, nyni 20 vs 25.

To change the interface metric, follow these steps:

1. Click Start, click Run, type ncpa.cpl , and then click OK.
   
   The available connections appear in the LAN and High-Speed Internet section of the Network Connections window.
2. Right-click the network adapter that you want to change, click Properties, and then click the General tab.
3. In the This connection uses the following items box, select Internet Protocol (TCP/IP). Then, click Properties.
4. In the Internet Protocol (TCP/IP) Properties dialog box, click the General tab, and then click Advanced.
5. On the IP Settings tab, click to clear the Automatic metric check box. Then, type a value in the Interface metric box.

Pote pujde na kabel vse z rozsahu 10.8.0.1 - 10.9.255.254.

2) Pokud je teda potreba na kabel posilat skutecne vse z 10.*, tak je potreba jeste ten jeden prikaz viz Jezevec:

route -p add 10.0.0.0 mask 255.0.0.0 10.10.8.1

[steelman]

Monsoon: Dik presne toto som potreboval. Konecne mozem plnohodnotne pracovat