Výsledky 1 až 14 z 14

Téma: WD400BB - blizi sa koniec?

  1. #1

    Standardní WD400BB - blizi sa koniec?

    Mam ho uz skoro 3 roky (vyrobeny bol 4/2001), doteraz bez problemov. Dnes som defragmentoval disk a pri tom mi to zamrzlo, LEDka svietila a z disku sa ozyvali slabe divne zvuky (pokusal sa precitat dokola to iste). Tak som to resetoval a pustil rucne scandisk. Zastavil sa na chybe, ze bad sector a treba pustit thorough test.
    Nabootoval som z diskety od WD a quick test mi povedal, ze na disku su chyby, ktore mozu byt opravitelne a spytal sa, ci ich chcem opravit. Dal som nie, disk pripojil do druheho PC a zalohoval vsetko dolezite (zaujimave, ze ked treba, tak obsah 40GB disku vojde na 30GB disk, na ktorom je uz kopa vselicoho ).
    Potom som to dal "opravit" tou diagnostikou od WD. Po "opraveni" uz quick test presiel bez problemov, tak som spustil este extended test - ten skoncil s chybou 0357. Tak som dal write zeros a to teraz bezi (asi 2 a pol hodiny) - som zvedavy, co z toho bude...
    Stretol sa niekto s takymto problemom pri diskoch WD?
    A este trochu OT otazka: aky disk mam kupit? WD1200JB alebo Samsung SP1213N? IBM/Hitachi, Maxtor ani Seagate nechcem.
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  2. #2

    Standardní

    Co ten beďar?? Je jen jeden, nebo je jich víc, je jejich počet stálý nebo se zvětšují?? Pokud ne disk by byl ještě vcelku použitelný, kdyžtak se podívej na moje stránky o bad sectorech http://apokeus.wz.cz (prosím ale toleranci co se týče mé angličtiny )
    jinak doporučuju seagate

  3. #3

    Standardní

    Neviem, kolko ich tam bolo - scandisk som nenechal pusteny. Ale pri zalohovani sa mi nepodarilo precitat asi 5 suborov (medzi nimi aj USER.DAT ako vzdy pri chybe na disku...) Mam aj ulozeny vypis zo SMART (aj zo SMART logu poslednych par chyb) - ale mam to na Linuxovej particii a teraz som vo Windows.
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  4. #4

    Standardní

    Tak to bude zkřivená hlava, která bude dělat stále nové bad sectory , doporučuju ti to co jsi z disku nevytahal rychle zazálohovat, pokud si chces trochu zariskovat zkus low level format jako poslední pokus o záchranu disku.

  5. #5

    Standardní

    Teraz bezi write zeros, uz je to skoro na konci. Potom pustim znovu testy a ked to prejde, tak FDISK+format a pozriem do SMARTu - aky je status a ci pribudaju chyby do logu.
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  6. #6
    Moderátor Avatar uživatele daso
    Založen
    07.10.2002
    Bydliště
    Praha, Ceska Lipa
    Příspěvky
    2 462
    Vliv
    290

    Standardní

    tak se taky pridam (Barracuda IV80GB)...
    dneska jsem s tim delal co slo, ale vypada to, ze disk konci. jeste "docela" jede. seatools jsem odstranim BB (jelo to snad 6hodin), ale je zabrzdeny (ke konci disku rychlost rapidne klesa) a ma problemy se smart.

    vypis z Active SMART
    ASRock ALiveNF6P-VSTA | AMD Athlon64 (Orleans) 1,8@2,4 GHz 1,4 V | 2,5 GB DDR2 | nVIDIA GeForce 7600 GS | MAXTOR DM10 250 GB | LG GSA-4165B
    ---
    ◄ ΔΑςΙΔ ΒΟΩΙΕ ►
    On the 8th day God created David Bowie.

  7. #7

    Standardní

    Takze write zeros skoncilo bez chyby a extended test tiez presiel bez chyby. Zajtra pozriem do SMARTu...
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  8. #8

    Standardní

    SMART pred zalohovanim:
    Kód:
    smartctl version 5.1-18 Copyright (C) 2002-3 Bruce Allen
    Home page is http://smartmontools.sourceforge.net/
    
    === START OF INFORMATION SECTION ===
    Device Model:     WDC WD400BB-00AUA1
    Serial Number:    WD-WMA6R3401126
    Firmware Version: 18.20D18
    Device is:        Not in smartctl database [for details use: -P showall]
    ATA Version is:   5
    ATA Standard is:  Exact ATA specification draft version not indicated
    Local Time is:    Fri Jan 23 20:00:08 2004 CET
    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled
    
    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED
    
    General SMART Values:
    Off-line data collection status: (0x84) Offline data collection activity was
                                            suspended by an interrupting command from host.
                                            Auto Off-line Data Collection: Enabled.
    Self-test execution status:      (   0) The previous self-test routine completed
                                            without error or no self-test has ever
                                            been run.
    Total time to complete off-line
    data collection:                 (2040) seconds.
    Offline data collection
    capabilities:                    (0x1b) SMART execute Offline immediate.
                                            Automatic timer ON/OFF support.
                                            Suspend Offline collection upon new
                                            command.
                                            Offline surface scan supported.
                                            Self-test supported.
                                            No Conveyance Self-test supported.
                                            No Selective Self-test supported.
    SMART capabilities:            (0x0003) Saves SMART data before entering
                                            power-saving mode.
                                            Supports SMART auto save timer.
    Error logging capability:        (0x01) Error logging supported.
                                            No General Purpose Logging support.
    Short self-test routine
    recommended polling time:        (   2) minutes.
    Extended self-test routine
    recommended polling time:        (  32) minutes.
    
    SMART Attributes Data Structure revision number: 16
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
      1 Raw_Read_Error_Rate     0x000b   200   074   051    Pre-fail  Always       -       0
      3 Spin_Up_Time            0x0007   133   100   021    Pre-fail  Always       -       2166
      4 Start_Stop_Count        0x0032   098   098   040    Old_age   Always       -       2077
      5 Reallocated_Sector_Ct   0x0032   200   200   112    Old_age   Always       -       0
      7 Seek_Error_Rate         0x000b   100   253   051    Pre-fail  Always       -       0
      9 Power_On_Hours          0x0032   086   086   000    Old_age   Always       -       10774
     10 Spin_Retry_Count        0x0013   100   098   051    Pre-fail  Always       -       2
     11 Calibration_Retry_Count 0x0013   100   100   051    Pre-fail  Always       -       0
     12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1754
    196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
    197 Current_Pending_Sector  0x0012   193   193   000    Old_age   Always       -       50
    198 Offline_Uncorrectable   0x0012   200   200   000    Old_age   Always       -       0
    199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       6
    200 Multi_Zone_Error_Rate   0x0009   200   200   051    Pre-fail  Offline      -       0
    
    SMART Error Log Version: 1
    ATA Error Count: 102 (device log contains only the most recent five errors)
            CR = Command Register [HEX]
            FR = Features Register [HEX]
            SC = Sector Count Register [HEX]
            SN = Sector Number Register [HEX]
            CL = Cylinder Low Register [HEX]
            CH = Cylinder High Register [HEX]
            DH = Device/Head Register [HEX]
            DC = Device Command Register [HEX]
            ER = Error register [HEX]
            ST = Status register [HEX]
    Timestamp = decimal seconds since the previous disk power-on.
    Note: timestamp "wraps" after 2^32 msec = 49.710 days.
    
    Error 102 occurred at disk power-on lifetime: 943 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 ea 2b 86 e0
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      20 00 01 ea 2b 86 e0 00    2719.050  READ SECTOR(S)
      20 00 08 a7 03 5f e1 00    2719.050  READ SECTOR(S)
      20 00 08 67 1c 86 e0 00    2719.050  READ SECTOR(S)
      20 00 08 a7 72 95 e0 00    2719.050  READ SECTOR(S)
      20 00 08 27 c0 03 e0 00    2719.000  READ SECTOR(S)
    
    Error 101 occurred at disk power-on lifetime: 943 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 ea 2b 86 e0
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      20 00 01 ea 2b 86 e0 00    2663.100  READ SECTOR(S)
      20 00 08 67 06 6b e1 00    2663.100  READ SECTOR(S)
      20 00 08 a7 f3 6a e1 00    2663.050  READ SECTOR(S)
      91 00 3f 01 00 00 fe 0a    2662.950  INITIALIZE DEVICE PARAMETERS [OBS-6]
      10 00 01 01 00 00 a0 08    2662.950  RECALIBRATE [OBS-4]
    
    Error 100 occurred at disk power-on lifetime: 943 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 ea 2b 86 e0
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      20 00 01 ea 2b 86 e0 00    2653.700  READ SECTOR(S)
      20 00 01 ee 2b 86 e0 00    2653.650  READ SECTOR(S)
      20 00 01 ed 2b 86 e0 00    2653.650  READ SECTOR(S)
      20 00 01 ec 2b 86 e0 00    2653.650  READ SECTOR(S)
      20 00 01 eb 2b 86 e0 00    2653.650  READ SECTOR(S)
    
    Error 99 occurred at disk power-on lifetime: 943 hours
      When the command that caused the error occurred, the device was doing SMART off-line or self test.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 ea 2b 86 e0
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      20 00 01 ea 2b 86 e0 00    2644.550  READ SECTOR(S)
      20 00 01 e9 2b 86 e0 00    2644.550  READ SECTOR(S)
      20 00 01 e8 2b 86 e0 00    2644.550  READ SECTOR(S)
      20 00 01 e7 2b 86 e0 00    2644.550  READ SECTOR(S)
      91 00 3f 01 00 00 fe 0a    2644.450  INITIALIZE DEVICE PARAMETERS [OBS-6]
    
    Error 98 occurred at disk power-on lifetime: 943 hours
      When the command that caused the error occurred, the device was doing SMART off-line or self test.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 08 ea 2b 86 e0
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      20 00 08 e7 2b 86 e0 00    2635.300  READ SECTOR(S)
      20 00 08 e7 00 7f e0 00    2635.300  READ SECTOR(S)
      20 00 08 a7 30 02 e0 00    2623.250  READ SECTOR(S)
      20 00 08 67 3d e2 e0 00    2604.800  READ SECTOR(S)
      20 00 08 67 b9 f7 e0 00    2604.750  READ SECTOR(S)
    
    SMART Self-test log structure revision number 1
    Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
    # 1  Short captive       Completed without error       00%       458         -
    # 2  Short captive       Interrupted (host reset)      80%       938         -
    SMART po zalohovani a po write zeros:
    Kód:
    smartctl version 5.1-18 Copyright (C) 2002-3 Bruce Allen
    Home page is http://smartmontools.sourceforge.net/
    
    === START OF INFORMATION SECTION ===
    Device Model:     WDC WD400BB-00AUA1
    Serial Number:    WD-WMA6R3401126
    Firmware Version: 18.20D18
    Device is:        Not in smartctl database [for details use: -P showall]
    ATA Version is:   5
    ATA Standard is:  Exact ATA specification draft version not indicated
    Local Time is:    Sat Jan 24 10:51:03 2004 CET
    SMART support is: Available - device has SMART capability.
    SMART support is: Enabled
    
    === START OF READ SMART DATA SECTION ===
    SMART overall-health self-assessment test result: PASSED
    
    General SMART Values:
    Off-line data collection status: (0x85) Offline data collection activity was
                                            aborted by an interrupting command from host.
                                            Auto Off-line Data Collection: Enabled.
    Self-test execution status:      (   0) The previous self-test routine completed
                                            without error or no self-test has ever
                                            been run.
    Total time to complete off-line
    data collection:                 (2040) seconds.
    Offline data collection
    capabilities:                    (0x1b) SMART execute Offline immediate.
                                            Automatic timer ON/OFF support.
                                            Suspend Offline collection upon new
                                            command.
                                            Offline surface scan supported.
                                            Self-test supported.
                                            No Conveyance Self-test supported.
                                            No Selective Self-test supported.
    SMART capabilities:            (0x0003) Saves SMART data before entering
                                            power-saving mode.
                                            Supports SMART auto save timer.
    Error logging capability:        (0x01) Error logging supported.
                                            No General Purpose Logging support.
    Short self-test routine
    recommended polling time:        (   2) minutes.
    Extended self-test routine
    recommended polling time:        (  32) minutes.
    
    SMART Attributes Data Structure revision number: 16
    Vendor Specific SMART Attributes with Thresholds:
    ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
      1 Raw_Read_Error_Rate     0x000b   194   074   051    Pre-fail  Always       -       73
      3 Spin_Up_Time            0x0007   126   100   021    Pre-fail  Always       -       2525
      4 Start_Stop_Count        0x0032   098   098   040    Old_age   Always       -       2082
      5 Reallocated_Sector_Ct   0x0032   200   200   112    Old_age   Always       -       0
      7 Seek_Error_Rate         0x000b   200   200   051    Pre-fail  Always       -       0
      9 Power_On_Hours          0x0032   086   086   000    Old_age   Always       -       10778
     10 Spin_Retry_Count        0x0013   100   098   051    Pre-fail  Always       -       2
     11 Calibration_Retry_Count 0x0013   100   100   051    Pre-fail  Always       -       0
     12 Power_Cycle_Count       0x0032   099   099   000    Old_age   Always       -       1759
    196 Reallocated_Event_Count 0x0032   200   200   000    Old_age   Always       -       0
    197 Current_Pending_Sector  0x0012   200   193   000    Old_age   Always       -       0
    198 Offline_Uncorrectable   0x0012   200   200   000    Old_age   Always       -       0
    199 UDMA_CRC_Error_Count    0x000a   200   253   000    Old_age   Always       -       7
    200 Multi_Zone_Error_Rate   0x0009   200   200   051    Pre-fail  Offline      -       0
    
    SMART Error Log Version: 1
    ATA Error Count: 112 (device log contains only the most recent five errors)
            CR = Command Register [HEX]
            FR = Features Register [HEX]
            SC = Sector Count Register [HEX]
            SN = Sector Number Register [HEX]
            CL = Cylinder Low Register [HEX]
            CH = Cylinder High Register [HEX]
            DH = Device/Head Register [HEX]
            DC = Device Command Register [HEX]
            ER = Error register [HEX]
            ST = Status register [HEX]
    Timestamp = decimal seconds since the previous disk power-on.
    Note: timestamp "wraps" after 2^32 msec = 49.710 days.
    
    Error 112 occurred at disk power-on lifetime: 944 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 b3 30 11 e3
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      c8 00 01 b3 30 11 e3 00    1101.100  READ DMA
      c8 00 01 b6 30 11 e3 00    1101.000  READ DMA
      c8 00 01 b5 30 11 e3 00    1100.900  READ DMA
      c8 00 01 b4 30 11 e3 00    1100.900  READ DMA
      c8 00 08 37 4d 7a e0 00    1100.900  READ DMA
    
    Error 111 occurred at disk power-on lifetime: 944 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 b3 30 11 e3
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      c8 00 01 b3 30 11 e3 00    1091.600  READ DMA
      c8 00 08 8f 3d 7a e0 00    1091.600  READ DMA
      c8 00 01 b2 30 11 e3 00    1091.500  READ DMA
      c8 00 08 67 42 7a e0 00    1091.500  READ DMA
      c8 00 01 b1 30 11 e3 00    1091.400  READ DMA
    
    Error 110 occurred at disk power-on lifetime: 944 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 08 b3 30 11 e3
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      c8 00 08 af 30 11 e3 00    1080.950  READ DMA
      c8 00 08 bf 5f 08 e0 00    1080.950  READ DMA
      c8 00 08 a7 30 11 e3 00    1080.300  READ DMA
      c8 00 08 87 44 51 e0 00    1080.300  READ DMA
      c8 00 08 9f 30 11 e3 00    1079.900  READ DMA
    
    Error 109 occurred at disk power-on lifetime: 944 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 7e 8c 30 11 e3
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      c8 00 7e 3d 30 11 e3 00    1068.400  READ DMA
      c8 00 7e bf 2f 11 e3 00    1068.400  READ DMA
      c8 00 7e 41 2f 11 e3 00    1068.400  READ DMA
      c8 00 7e c3 2e 11 e3 00    1068.400  READ DMA
      c8 00 7e 45 2e 11 e3 00    1068.400  READ DMA
    
    Error 108 occurred at disk power-on lifetime: 944 hours
      When the command that caused the error occurred, the device was active or idle.
    
      After command completion occurred, registers were:
      ER ST SC SN CL CH DH
      -- -- -- -- -- -- --
      40 51 01 2c 3d 79 e1
    
      Commands leading to the command that caused the error were:
      CR FR SC SN CL CH DH DC   Timestamp  Command/Feature_Name
      -- -- -- -- -- -- -- --   ---------  --------------------
      40 00 01 2c 3d 79 e1 00     764.850  READ VERIFY SECTOR(S)
      40 00 01 2b 3d 79 e1 00     758.800  READ VERIFY SECTOR(S)
      40 00 01 2a 3d 79 e1 00     753.350  READ VERIFY SECTOR(S)
      40 00 01 29 3d 79 e1 00     747.800  READ VERIFY SECTOR(S)
      40 00 01 28 3d 79 e1 00     741.750  READ VERIFY SECTOR(S)
    
    SMART Self-test log structure revision number 1
    Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
    # 1  Short captive       Completed without error       00%       944         -
    # 2  Short captive       Completed without error       00%       944         -
    # 3  Short captive       Completed without error       00%       458         -
    # 4  Short captive       Interrupted (host reset)      80%       938         -
    Stav z ActiveSMART (je to uplny shit oproti smartctl):
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  9. #9
    Moderátor mince Avatar uživatele peta303
    Založen
    21.09.2003
    Bydliště
    PHA 4
    Věk
    41
    Příspěvky
    2 413
    Vliv
    292

    Standardní Re: WD400BB - blizi sa koniec?

    Citace Původně odeslal Rainbow
    Mam ho uz skoro 3 roky (vyrobeny bol 4/2001), doteraz bez problemov. Dnes som defragmentoval disk a pri tom mi to zamrzlo, LEDka svietila a z disku sa ozyvali slabe divne zvuky (pokusal sa precitat dokola to iste). Tak som to resetoval a pustil rucne scandisk. Zastavil sa na chybe, ze bad sector a treba pustit thorough test.
    Nabootoval som z diskety od WD a quick test mi povedal, ze na disku su chyby, ktore mozu byt opravitelne a spytal sa, ci ich chcem opravit. Dal som nie, disk pripojil do druheho PC a zalohoval vsetko dolezite (zaujimave, ze ked treba, tak obsah 40GB disku vojde na 30GB disk, na ktorom je uz kopa vselicoho ;D ).
    Potom som to dal "opravit" tou diagnostikou od WD. Po "opraveni" uz quick test presiel bez problemov, tak som spustil este extended test - ten skoncil s chybou 0357. Tak som dal write zeros a to teraz bezi (asi 2 a pol hodiny) - som zvedavy, co z toho bude...
    Stretol sa niekto s takymto problemom pri diskoch WD?
    A este trochu OT otazka: aky disk mam kupit? WD1200JB alebo Samsung SP1213N? IBM/Hitachi, Maxtor ani Seagate nechcem.
    Přesně tohle mi udělal po roce a půl provozu (vyroben 12'01, v provozu od 1'02, odešel 7'03). Write zeros pomohlo zhruba na měsíc, pak stejná chyba (0357 DAM, sektory alokovány někam do pr...) SMART status vždycky zalítal jak šílenej. Jinak na ATA100 už potom neběžel, protože tam od zhroucení se nikdy neprošel testem. Na ATA33 se mi ho povedlo "opravit", pak se stejně vysypal znova.

    Bez problémů mi to vyreklamovali za nový disk, akorát to chvilku trvalo. Radši neotálej s reklamací.
    NB DELL E5480 (i5 7440HQ, 16 GB DDR4 Micron, 1 TB Micron)
    PC Athlon X2 4600+, AC Alpine 64, ASUS M2A-VM, 4 GB DDR2 Transcend, HD2400 PRO, SB Live!, 3,5" TEAC, NEC ND-3520A, NEC AD-7203A, Transcend SSD 370 / 120, WD RED 2 TB, Fortron 400 PNF, EC ML-5410A, Chicony 2961, Genius NSO+, TESLA AZS 223 + TESLA ARS 1014, TESLA NC 470, TESLA SM 260, TESLA SM 261, TESLA B-101, HP 5820, 2x DELL 2009Wfp
    PC2 DELL Optiplex 5020 (i5 4590, 8 GB DDR3 Kingston, HD5450, Crucial 240 GB, DELL 2009Wt
    photo Nikon D90, Nikkor 18-70, Nikkor 24-120, Sigma 70-300, SB800

  10. #10

    Standardní

    Ten tvoj bol ten stary typ:

    alebo ten novsi v EBckovom obale?
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  11. #11
    Moderátor mince Avatar uživatele peta303
    Založen
    21.09.2003
    Bydliště
    PHA 4
    Věk
    41
    Příspěvky
    2 413
    Vliv
    292

    Standardní

    Citace Původně odeslal Rainbow
    Ten tvoj bol ten stary typ:

    alebo ten novsi v EBckovom obale?
    Byl to ten starý. "EB-like" jsem dostal až po reklamaci. Vím, kam tím míříš. Jinak ty "EBčkové" nemají krytou elektroniku (že by na tom obrázku byl vzorek?) a bohužel se dnes v tomhle pouzdru dodává i 800JB... :-/

    Měl jsem o tom někde na foru i thread, ale už je to 3 měsíce zpátky, takže bude asi smazaný.
    NB DELL E5480 (i5 7440HQ, 16 GB DDR4 Micron, 1 TB Micron)
    PC Athlon X2 4600+, AC Alpine 64, ASUS M2A-VM, 4 GB DDR2 Transcend, HD2400 PRO, SB Live!, 3,5" TEAC, NEC ND-3520A, NEC AD-7203A, Transcend SSD 370 / 120, WD RED 2 TB, Fortron 400 PNF, EC ML-5410A, Chicony 2961, Genius NSO+, TESLA AZS 223 + TESLA ARS 1014, TESLA NC 470, TESLA SM 260, TESLA SM 261, TESLA B-101, HP 5820, 2x DELL 2009Wfp
    PC2 DELL Optiplex 5020 (i5 4590, 8 GB DDR3 Kingston, HD5450, Crucial 240 GB, DELL 2009Wt
    photo Nikon D90, Nikkor 18-70, Nikkor 24-120, Sigma 70-300, SB800

  12. #12

    Standardní

    Prave som tam vsetko nakopiroval a idem to trochu otestovat.
    V pondelok pojdem asi kupit Samsung...
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  13. #13

    Standardní

    Teraz mam ten disk spolu s WD300BB v jednom PC. Ten WD300BB je podstatne tichsi - a myslim, ze ten 400BB nebol taky hlucny, ked bol novy - takze sa asi nejako vydralo lozisko...
    Zatazujem ho - kopirujem a pod. - a tvari sa, ze mu vobec nic nie je. RAW Read Error Rate je stale 200, do logu nepribudli ziadne chyby. Este skusim pustit SMART long test, ale to az ked budem v Linuxe (pre Windows na to asi neexistuje ziadny program )
    1: Asus P2B 1.10 • Celeron 1100@1364/1.8V • 512MB SDRAM • Samsung SP1213N+WD AC28400 • Toshiba XM-6402B+SD-M1212 • PowerColor AR2L Radeon 9100 64MB • 3C900-Combo • Bt848A • ASB-3940UA • AWE-64 • DTK PTP-3007 • VisionMaster 405 • Umax UC630 • Star LC24-200 Colour 2: PCPartner TXB820DS • Cyrix MII PR300/1.8V • 256MB SDRAM • 2xSamsung HD400LD+IT8212F • Accesstek CW4001 • LS-120 • Mystique 4MB • Millennium II 4MB • 3C509 • CMI8329A+Dream MIDI • ADI ProVista E44 • SyncMaster 203B Notebook: DTK FortisPro TOP-5A • P166MMX/1.8V • 80MB EDO • Hitachi 5K80 40GB • 12,1" TFT Router: A-Trend ATC-1425B • i486DX 50@33/5V • 48MB FPM • WD AC14300 • UMC UM9003F • HP PC LAN 16/TP+ Car: Mazda 323P BA • Z5 1489ccm, 65kW@5500rpm, 134Nm@4000rpm

  14. #14
    Moderátor mince Avatar uživatele peta303
    Založen
    21.09.2003
    Bydliště
    PHA 4
    Věk
    41
    Příspěvky
    2 413
    Vliv
    292

    Standardní

    Citace Původně odeslal Rainbow
    Teraz mam ten disk spolu s WD300BB v jednom PC. Ten WD300BB je podstatne tichsi - a myslim, ze ten 400BB nebol taky hlucny, ked bol novy - takze sa asi nejako vydralo lozisko...
    Zatazujem ho - kopirujem a pod. - a tvari sa, ze mu vobec nic nie je. RAW Read Error Rate je stale 200, do logu nepribudli ziadne chyby. Este skusim pustit SMART long test, ale to az ked budem v Linuxe (pre Windows na to asi neexistuje ziadny program :evil: )
    Ano, chová se naprosto stejně jako ten můj... Každopádně ho byla škoda.
    Zvýšenou hlučnost jsem pozoroval rovněž, ale drnčel jen někdy a spíš výjimečně.

    Jinak já měl problém někde na hranici 27.GB. (~69%).
    NB DELL E5480 (i5 7440HQ, 16 GB DDR4 Micron, 1 TB Micron)
    PC Athlon X2 4600+, AC Alpine 64, ASUS M2A-VM, 4 GB DDR2 Transcend, HD2400 PRO, SB Live!, 3,5" TEAC, NEC ND-3520A, NEC AD-7203A, Transcend SSD 370 / 120, WD RED 2 TB, Fortron 400 PNF, EC ML-5410A, Chicony 2961, Genius NSO+, TESLA AZS 223 + TESLA ARS 1014, TESLA NC 470, TESLA SM 260, TESLA SM 261, TESLA B-101, HP 5820, 2x DELL 2009Wfp
    PC2 DELL Optiplex 5020 (i5 4590, 8 GB DDR3 Kingston, HD5450, Crucial 240 GB, DELL 2009Wt
    photo Nikon D90, Nikkor 18-70, Nikkor 24-120, Sigma 70-300, SB800

Informace o tématu

Users Browsing this Thread

Toto téma si právě prohlíží 1 uživatelů. (0 registrovaných a 1 anonymních)

Pravidla přispívání

  • Nemůžete zakládat nová témata
  • Nemůžete zasílat odpovědi
  • Nemůžete přikládat přílohy
  • Nemůžete upravovat své příspěvky
  •