Gentoo 2005.0 Ati fglrx

[..::Ozzy::..]

Nainstaloval jsem gentoo bez jakych kolik problemu a jiz jsem nakonfiguroval velkou cast, ale dneska doopledne jsem si chtel odladit
grafiku a nevim co me to napadlo, ale pomoci rpm2gzip jsem rozbalil fglrx drivery od ATi na xorg a spustil jsem tam inicializcni souboru.
Po restartu to na me kriklo ze to nemuze najit modul ati_dri.o nebo neco tomu podobny...
Tak jsem nasel neco na wiki.org tak jsem prekopilil kernel s ati podporou jako modul a situace se nemeni...


Poradte... jeste budu hledat a zkouset, ale pokud nekdo vite tak napiste...
Pokud to vyresim tak to sem hodim

[Gargamel]

emerge ati-drivers?

Jinak s fglrx sou problemy, to je jasne, doporucuju predtim vypnout framebuffer (mozna bude vadit i vesa), nenatahovat zadne moduly radeon a agpgart. V tom ebuildu sou jeste nejake instrukce, tak se jimi rid

[Dr Meduza]

fglrx zavisi na modulu agpgart ne

trechu se vetru me sice jede obraz i nak akcelerace (glxgears cca 1800FPS na defaultni okno s R9100) ale ted sem tu zkousel kompilovat par vecicek s CristalSpace enginem a problem ono to na HW jede vo dost pomalejc nez na SW a kdyz se tam da podpora novyho enginu tak to sice jede ale dela to chyby v obraze

[..::Ozzy::..]

fglrx zavisi na modulu agpgart ne

taky si myslim

jinak emerge ati-drivers jsem jiz pouzil

podle tohohle jsem to dal vse zase zpět dopořádku

http://odin.prohosting.com/wedge01/g...adeon-faq.html

[Dr Meduza]

tak sem updatoval na 8.12.10 a vypada ze uz to jede spravne
akorat prestal chodit ten ovladac na AGP v ovladacaich takze sem musel hodit ten co je v jadru ale to by nemelo mit nakej zasadni vliv ne?
//edit: hm tak stejnej problem nektery veci dou furt pomalu ale zacnou jit pomalu az za chvili

[..::Ozzy::..]

tak vsechno spatne 2x to nabehne a po treti to hlasi ze nemuze najit etc/lib/module/...................../radeon_drv.o

kdyz pustim

emerge --update --deep --newuse world

tak mi to blokujou ovladace ati-drivers

nejakej napady

[Gargamel]

tak vsechno spatne 2x to nabehne a po treti to hlasi ze nemuze najit etc/lib/module/...................../radeon_drv.o

radeon_drv je cast DRI - pokud pouzivas primo binarni ATI ovladace, nesmi byt tento modul natazen - do jadra se musi natahnout jenom modul fglrx.

Co se tyce agpgartu - tusimze se to da v x.org konfiguraku nastavit, jestli bude fglrx pouzivat vlastni agpgart nebo systemovy - chce to prozkouset, se kterym to bude chodit lip.

Co se tyce CrystalSpace - ujisti se, ze mas aktivni spravnou libGL.so z baliku fglrx, ono to pak muze delat ruzne haluze.

BTW ja mam na R9200 s DRI driverama cca 2200 fps v glxgears (ale tohle neni meritko vykonu...)

[..::Ozzy::..]

Ok zkusim a dam vedet

[..::Ozzy::..]

http://odin.prohosting.com/wedge01/g....html#1_whyuse
našel jsem na zahraničních fórech nějaké podrobnější návody tak se to pokusim udělat podle nich.

tak ja uz fakt nevim

emerge ati-drivers

OK

opengl-update ati

OK

Vesker nastaveni jadra je podle navodu

glxinfo

name of display: :0.0
display: :0  screen: 0
direct rendering: No
server glx vendor string: SGI
server glx version string: 1.2
server glx extensions:
    GLX_ARB_multisample, GLX_EXT_visual_info, GLX_EXT_visual_rating,
    GLX_EXT_import_context, GLX_OML_swap_method, GLX_SGI_make_current_read,
    GLX_SGIS_multisample, GLX_SGIX_fbconfig
client glx vendor string: ATI
client glx version string: 1.3
client glx extensions:
    GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
    GLX_ARB_get_proc_address, GLX_ARB_multisample, GLX_ATI_pixel_format_float,
    GLX_ATI_render_texture
GLX extensions:
    GLX_EXT_visual_info, GLX_EXT_visual_rating, GLX_EXT_import_context,
    GLX_ARB_multisample
OpenGL vendor string: Mesa project: www.mesa3d.org
OpenGL renderer string: Mesa GLX Indirect
OpenGL version string: 1.2 (1.5 Mesa 6.2.1)
OpenGL extensions:
    GL_ARB_imaging, GL_ARB_multitexture, GL_ARB_texture_border_clamp,
    GL_ARB_texture_cube_map, GL_ARB_texture_env_add,
    GL_ARB_texture_env_combine, GL_ARB_texture_env_dot3,
    GL_ARB_transpose_matrix, GL_EXT_abgr, GL_EXT_blend_color,
    GL_EXT_blend_minmax, GL_EXT_blend_subtract, GL_EXT_texture_env_add,
    GL_EXT_texture_env_combine, GL_EXT_texture_env_dot3,
    GL_EXT_texture_lod_bias
glu version: 1.3
glu extensions:
    GLU_EXT_nurbs_tessellator, GLU_EXT_object_space_tess

   visual  x  bf lv rg d st colorbuffer ax dp st accumbuffer  ms  cav
 id dep cl sp sz l  ci b ro  r  g  b  a bf th cl  r  g  b  a ns b eat
----------------------------------------------------------------------
0x23 24 tc  0 24  0 r  y  .  8  8  8  0  0 16  0  0  0  0  0  1 0 None
0x24 24 tc  0 24  0 r  y  .  8  8  8  0  0 16  8 16 16 16  0  1 0 None
0x25 24 tc  0 32  0 r  y  .  8  8  8  8  0 16  8 16 16 16 16  1 0 None
0x26 24 tc  0 32  0 r  .  .  8  8  8  8  0 16  8 16 16 16 16  1 0 None
0x27 24 dc  0 24  0 r  y  .  8  8  8  0  0 16  0  0  0  0  0  1 0 None
0x28 24 dc  0 24  0 r  y  .  8  8  8  0  0 16  8 16 16 16  0  1 0 None
0x29 24 dc  0 32  0 r  y  .  8  8  8  8  0 16  8 16 16 16 16  1 0 None
0x2a 24 dc  0 32  0 r  .  .  8  8  8  8  0 16  8 16 16 16 16  1 0 None

/etc/X11/xorg.conf

# File generated by xorgconfig.

#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
#
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
#
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
#
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#

# **********************************************************************
# Refer to the xorg.conf(5x) man page for details about the format of
# this file.
# **********************************************************************

# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
Section "Module"

# This loads the DBE extension module.

    Load        "dbe"   # Double buffer extension

# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection  "extmod"
      Option    "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection

# This loads the font modules
    Load        "type1"
#    Load        "speedo"
    Load        "freetype"
#    Load        "xtt"

# This loads the GLX module
    Load       "glx"
# This loads the DRI module
    Load       "dri"

EndSection

# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.

    RgbPath     "/usr/X11R6/lib/X11/rgb"

# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
#
#

    FontPath   "/usr/share/fonts/misc/"
    FontPath   "/usr/share/fonts/TTF/"
    FontPath   "/usr/share/fonts/Type1/"
#    FontPath   "/usr/share/fonts/CID/"
    FontPath   "/usr/share/fonts/75dpi/"
    FontPath   "/usr/share/fonts/100dpi/"
    FontPath   "/usr/share/fonts/local/"
#    FontPath   "/usr/share/fonts/Speedo/"
#    FontPath   "/usr/share/fonts/TrueType/"
#    FontPath   "/usr/share/fonts/freefont/"

# The module search path.  The default path is shown here.

#    ModulePath "/usr/X11R6/lib/modules"

EndSection

# **********************************************************************
# Server flags section.
# **********************************************************************

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging

#    Option "NoTrapSignals"

# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# &#40;where n is 1 through 12&#41;.  This allows clients to receive these key
# events.

#    Option "DontVTSwitch"

# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.

#    Option "DontZap"

# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.

#    Option "Dont Zoom"

# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.

#    Option "DisableVidModeExtension"

# Uncomment this to enable the use of a non-local xvidtune client.

#    Option "AllowNonLocalXvidtune"

# Uncomment this to disable dynamically modifying the input device
# &#40;mouse and keyboard&#41; settings.

#    Option "DisableModInDev"

# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings &#40;currently only xset&#41;.

#    Option "AllowNonLocalModInDev"

EndSection

# **********************************************************************
# Input devices
# **********************************************************************

# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************

Section "InputDevice"

    Identifier  "Keyboard1"
    Driver      "kbd"

# For most OSs the protocol can be omitted &#40;it defaults to "Standard"&#41;.
# When using XQUEUE &#40;only for SVR3 and SVR4, but not Solaris&#41;,
# uncomment the following line.

#    Option     "Protocol"      "Xqueue"

    Option "AutoRepeat" "500 30"

# Specify which keyboard LEDs can be user-controlled &#40;eg, with xset&#40;1&#41;&#41;
#    Option     "Xleds"      "1 2 3"

#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"

# To customise the XKB settings to suit your keyboard, modify the
# lines below &#40;which are the defaults&#41;.  For example, for a non-U.S.
# keyboard, you will probably want to use&#58;
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use&#58;
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with&#58;
#    Option "XkbLayout"   "de"
# or&#58;
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use&#58;
#    Option "XkbOptions"  "ctrl&#58;swapcaps"

# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""

#    Option "XkbDisable"

    Option "XkbRules"   "xorg"
    Option "XkbModel"   "pc105"
    Option "XkbLayout"  "cz"

EndSection


# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************

Section "InputDevice"

# Identifier and driver

    Identifier  "Mouse1"
    Driver      "mouse"
    Option "Protocol"    "ImPS/2"
    Option "ZAxisMapping" "4 5"
    Option "Device"      "/dev/psaux"

# Mouse-speed setting for PS/2 mouse.

#    Option "Resolution"        "256"

# When using XQUEUE, comment out the above two lines, and uncomment
# the following line.

#    Option "Protocol"  "Xqueue"

# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.

#    Option "BaudRate"  "9600"
#    Option "SampleRate"        "150"

# Emulate3Buttons is an option for 2-button Microsoft mice
# Emulate3Timeout is the timeout in milliseconds &#40;default is 50ms&#41;

#    Option "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"

# ChordMiddle is an option for some 3-button Logitech mice

#    Option "ChordMiddle"

EndSection


# **********************************************************************
# Other input device sections
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice"
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection

# **********************************************************************
# Monitor section
# **********************************************************************

# Any number of monitor sections may be present

Section "Monitor"

    Identifier  "My Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE&#58; THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    HorizSync   31.5 - 64.3

#    HorizSync  30-64         # multisync
#    HorizSync  31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync  15-25, 30-50  # multiple ranges of sync frequencies

# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE&#58; THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.

    VertRefresh 50-160

EndSection


# **********************************************************************
# Graphics device section
# **********************************************************************

# Any number of graphics device sections may be present

# Standard VGA Device&#58;

Section "Device"
    Identifier  "Standard VGA"
    VendorName  "Unknown"
    BoardName   "Unknown"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.

#    Chipset    "generic"

# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.

    Driver     "vga"
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.

#    BusID      "PCI&#58;0&#58;10&#58;0"

#    VideoRam   256

#    Clocks     25.2 28.3

EndSection

# Device configured by xorgconfig&#58;

Section "Device"
    Identifier  "ATI Graphics adapter"
    Driver      "fglrx"
    Option      "no_accel" "no"
    Option      "no_dri"   "no"
    Option      "VideoOverlay" "on"
    Option      "Capabilities" "0x00000000"
    Option      "OpenGLOverlay" "off"
    BusID       "PCI&#58;1&#58;0&#58;0"
        # unsupported card
    #VideoRam    131072
    # Insert Clocks lines here if appropriate
EndSection


# **********************************************************************
# Screen sections
# **********************************************************************

# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
Section "Screen"
    Identifier  "Screen 1"
    Device      "ATI Graphics adapter"
    Monitor     "My Monitor"
    DefaultDepth 24

    Subsection "Display"
        Depth       8
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       16
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
    Subsection "Display"
        Depth       24
        Modes       "1152x864" "1024x768" "800x600" "640x480"
        ViewPort    0 0
    EndSubsection
EndSection

# **********************************************************************
# ServerLayout sections.
# **********************************************************************

# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.

Section "ServerLayout"

# The Identifier line must be present
    Identifier  "Simple Layout"

# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.

    Screen "Screen 1"

# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".

    InputDevice "Mouse1" "CorePointer"
    InputDevice "Keyboard1" "CoreKeyboard"

EndSection

# Section "DRI"
#    Mode 0666
# EndSection

/var/log/Xorg.O.log
[code:1:70b5248f7c]
X Window System Version 6.8.2
Release Date: 9 February 2005
X Protocol Version 11, Revision 0, Release 6.8.2
Build Operating System: Linux 2.6.8-gentoo-r4 i686 [ELF]
Current Operating System: Linux OzzyTux 2.6.11-gentoo-r3 #3 SMP Tue May 17 21:13:20 GMT 2005 i686
Build Date: 12 March 2005
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.log", Time: Tue May 17 22:04:16 2005
(==) Using config file: "/etc/X11/xorg.conf"
(==) ServerLayout "Simple Layout"
(**) |-->Screen "Screen 1" (0)
(**) | |-->Monitor "My Monitor"
(**) | |-->Device "ATI Graphics adapter"
(**) |-->Input Device "Mouse1"
(**) |-->Input Device "Keyboard1"
(**) FontPath set to "/usr/share/fonts/misc/,/usr/share/fonts/TTF/,/usr/share/fonts/Type1/,/usr/share/fonts/75dpi/,/usr/share/fonts/100dpi/,/usr/share/fonts/local/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/lib/modules"
(WW) Open APM failed (/dev/apm_bios) (No such file or directory)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.7
X.Org XInput driver : 0.4
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/lib/modules/fonts/libbitmap.a
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/lib/modules/libpcidata.a
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
Using vt 7
(--) using VT number 7

(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,3189 card 1106,0000 rev 80 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b198 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:09:0: chip 10ec,8139 card 10ec,8139 rev 10 class 02,00,00 hdr 00
(II) PCI: 00:10:0: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:2: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3104 card 1106,3104 rev 82 class 0c,03,20 hdr 00
(II) PCI: 00:11:0: chip 1106,3177 card 1106,0000 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:1: chip 1106,0571 card 1106,0571 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:11:5: chip 1106,3059 card 4005,4720 rev 50 class 04,01,00 hdr 00
(II) PCI: 01:00:0: chip 1002,4152 card 174b,7c19 rev 00 class 03,00,00 hdr 80
(II) PCI: 01:00:1: chip 1002,4172 card 174b,7c18 rev 00 class 03,80,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 I/O range:
[0] -1 0 0x0000c000 - 0x0000c0ff (0x100) IX[B]
[1] -1 0 0x0000c400 - 0x0000c4ff (0x100) IX[B]
[2] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B]
[3] -1 0 0x0000cc00 - 0x0000ccff (0x100) IX[B]
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xdfe00000 - 0xdfefffff (0x100000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xbfd00000 - 0xdfcfffff (0x20000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) ATI Technologies Inc RV350 AR [Radeon 9600] rev 0, Mem @ 0xd0000000/27, 0xdfef0000/16, I/O @ 0xc800/8, BIOS @ 0xdfec0000/17
(--) PCI: (1:0:1) ATI Technologies Inc RV350 AR [Radeon 9600] (Secondary) rev 0, Mem @ 0xc8000000/27, 0xdfee0000/16
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xe0000000 from 0xe3ffffff to 0xdfffffff
(II) Active PCI resource ranges:
[0] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[1] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[2] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[3] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[4] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[5] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[6] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[7] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[8] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[9] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[10] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[11] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[12] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[1] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[2] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[3] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[4] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[5] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[6] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[7] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[8] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[9] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[10] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[11] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[12] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[6] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[7] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[8] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[9] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[10] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[11] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[17] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[18] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[19] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[20] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[21] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
(II) LoadModule: "dbe"
(II) Loading /usr/lib/modules/extensions/libdbe.a
(II) Module dbe: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension DOUBLE-BUFFER
(II) LoadModule: "extmod"
(II) Loading /usr/lib/modules/extensions/libextmod.a
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "type1"
(II) Loading /usr/lib/modules/fonts/libtype1.a
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "freetype"
(II) Loading /usr/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.8.2, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "glx"
(II) Loading /usr/lib/modules/extensions/libglx.a
(II) Module glx: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "GLcore"
(II) LoadModule: "GLcore"
(II) Loading /usr/lib/modules/extensions/libGLcore.a
(II) Module GLcore: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension GLX
(II) LoadModule: "dri"
(II) Loading /usr/lib/modules/extensions/libdri.a
(II) Module dri: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading sub module "drm"
(II) LoadModule: "drm"
(II) Loading /usr/lib/modules/linux/libdrm.a
(II) Module drm: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension XFree86-DRI
(II) LoadModule: "fglrx"
(II) Loading /usr/lib/modules/drivers/fglrx_drv.o
(II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
compiled for 4.3.99.902, module version = 8.8.25
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.7
(II) LoadModule: "mouse"
(II) Loading /usr/lib/modules/input/mouse_drv.o
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) LoadModule: "kbd"
(II) Loading /usr/lib/modules/input/kbd_drv.o
(II) Module kbd: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.4
(II) ATI Radeon/FireGL: The following chipsets are supported:
FireGL - (RV250 4964), FireGL - (RV250 4965),
RADEON 9000/9000 PRO (RV250 4966), RADEON 9000 LE (RV250 4967),
MOBILITY FireGL 9000 (M9 4C64), MOBILITY FireGL - (M9 4C65),
MOBILITY RADEON 9000 (M9 4C66), RADEON 9000 PRO &#409 4C67),
RADEON 9250 (RV280 5960), RADEON 9200 (RV280 5961),
RADEON 9200 SE (RV280 5964), MOBILITY RADEON 9200 (M9+ 5C61),
MOBILITY RADEON 9200 (M9+ 5C63), FireGL 8800 (R200 5148),
RADEON 8500 (R200 514C), RADEON 9100 (R200 514D),
RADEON - (R200 5154), RADEON - (R200 5155),
RADEON 8500 AIW (R200 4242), RADEON 9600 (RV350 4150),
RADEON 9600 SE (RV350 4151), RADEON 9600 PRO (RV360 4152),
MOBILITY RADEON 9600/9700 (M10/M11 4E50), RADEON 9500 (R300 4144),
RADEON - (R300 4145), RADEON 9600 TX (R300 4146),
FireGL Z1 (R300 4147), RADEON 9700 PRO (R300 4E44),
RADEON 9500 PRO/9700 (R300 4E45), RADEON 9600 TX (R300 4E46),
FireGL X1 (R300 4E47), RADEON 9800 SE (R350 4148),
FireGL - (R350 414B), RADEON 9550 (RV350 4153),
FireGL T2 (RV350 4154), FireGL - (RV350 4155), FireGL - (RV350 4156),
FireGL - (RV350 4157), RADEON 9800 PRO (R350 4E48),
RADEON 9800 (R350 4E49), RADEON 9800 XT (R360 4E4A),
FireGL X2-256/X2-256t (R350 4E4B),
MOBILITY FireGL T2/T2e (M10/M11 4E54), RADEON X300 (RV370 5B60),
RADEON - (RV370 5B61), RADEON X600 (RV380 5B62),
RADEON - (RV370 5B63), FireGL V3100 (RV370 5B64),
FireGL - (RV370 5B66), FireGL - (RV370 5B67),
MOBILITY RADEON X300 (M22 5460), MOBILITY RADEON - (M22 5461),
MOBILITY RADEON - (M22 5462), MOBILITY RADEON - (M22 5463),
MOBILITY FireGL V3100 (M22 5464), MOBILITY FireGL - (M22 5465),
MOBILITY FireGL - (M22 5466), MOBILITY FireGL - (M22 5467),
RADEON X600 (RV380 3E50), RADEON - (RV380 3E51),
RADEON - (RV380 3E52), RADEON - (RV380 3E53),
FireGL V3200 (RV380 3E54), FireGL - (RV380 3E55),
FireGL - (RV380 3E56), FireGL - (RV380 3E57),
MOBILITY RADEON X600 (M24 3150), MOBILITY RADEON - (M24 3151),
MOBILITY RADEON X300 (M22 3152), MOBILITY RADEON - (M24 3153),
MOBILITY FireGL V3200* (M24 3154), MOBILITY FireGL -* (M24 3155),
MOBILITY FireGL -* (M24 3156), MOBILITY FireGL -* (M24 3157),
RADEON X800 (R420 4A48), RADEON X800 PRO (R420 4A49),
RADEON X800 SE (R420 4A4A), RADEON X800 XT (R420 4A4B),
RADEON X800 (R420 4A4C), FireGL X3-256 (R420 4A4D),
MOBILITY RADEON 9800 (M18 4A4E),
RADEON X800 XT Platinum Edition (R420 4A50), RADEON X800 (R423 5548),
RADEON X800 PRO (R423 5549),
RADEON X800 XT Platinum Edition (R423 554A),
RADEON X800 SE (R423 554B), RADEON X800 XT (R423 5D57),
FireGL V7100 (R423 5550), FireGL V5100 (R423 5551),
FireGL -* (R423 5552), MOBILITY RADEON X800 XT (M28 5D48),
MOBILITY FireGL V5100* (M28 5D49), RADEON X700 XT (RV410 5E4A),
RADEON X700 PRO (RV410 5E4B), RADEON X700 SE (RV410 5E4C),
RADEON X700 (RV410 5E4D), RADEON X700 (RV410 5E4F),
RADEON - (RV410 5E52), RADEON - (RV410 5E53), RADEON - (RV410 5E55),
RADEON 9100 IGP (RS300 5834),
RADEON 9000 PRO/9100 PRO IGP (RS350 7834),
MOBILITY RADEON 9000/9100 IGP (RS300M 5835)
(II) Primary Device is: PCI 01:00:0
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found
(--) Chipset RADEON 9600 PRO (RV360 4152) found
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[6] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[7] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[8] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[9] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[10] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[11] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[13] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[14] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[15] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[16] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[17] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[18] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[19] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[20] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[21] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
(II) fglrx(0): pEnt->device->identifier=0x81f8390
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[6] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[7] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[8] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[9] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[10] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[11] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[12] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[19] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[20] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[21] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[22] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[23] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[24] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
[25] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[26] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) fglrx(0): === [R200PreInit] === begin, [s]
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/lib/modules/libvgahw.a
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(II) fglrx(0): PCI bus 1 card 0 func 0
(**) fglrx(0): Depth 24, (--) framebuffer bpp 32
(II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
(==) fglrx(0): Default visual is TrueColor
(**) fglrx(0): Option "NoAccel" "no"
(**) fglrx(0): Option "NoDRI" "no"
(**) fglrx(0): Option "Capabilities" "0x00000000"
(**) fglrx(0): Option "OpenGLOverlay" "off"
(**) fglrx(0): Option "VideoOverlay" "on"
(==) fglrx(0): Qbs disabled
(==) fglrx(0): RGB weight 888
(II) fglrx(0): Using 8 bits per RGB (8 bit DAC)
(==) fglrx(0): Gamma Correction for I is 0x06419064
(==) fglrx(0): Gamma Correction for II is 0x06419064
(==) fglrx(0): Buffer Tiling is ON
(II) Loading sub module "int10"
(II) LoadModule: "int10"
(II) Loading /usr/lib/modules/linux/libint10.a
(II) Module int10: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) fglrx(0): initializing int10
(II) fglrx(0): Primary V_BIOS segment is: 0xc000
(--) fglrx(0): Chipset: "RADEON 9600 PRO (RV360 4152)" (Chipset = 0x4152)
(--) fglrx(0): (PciSubVendor = 0x174b, PciSubDevice = 0x7c19)
(--) fglrx(0): board vendor info: third party grafics adapter - NOT original ATI
(--) fglrx(0): Linear framebuffer (phys) at 0xd0000000
(--) fglrx(0): MMIO registers at 0xdfef0000
(--) fglrx(0): ROM-BIOS at 0xdfec0000
(--) fglrx(0): ChipExtRevID = 0x00
(--) fglrx(0): ChipIntRevID = 0x0C
(--) fglrx(0): VideoRAM: 131072 kByte (64-bit SDR SDRAM)
(WW) fglrx(0): board is an unknown third party board, chipset is supported
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/lib/modules/libddc.a
(II) Module ddc: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.7
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/lib/modules/libi2c.a
(II) Module i2c: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
(II) fglrx(0): I2C bus "DDC" initialized.
(II) fglrx(0): Connector Layout from BIOS --------
(II) fglrx(0): Connector1: DDCType-3, DACType-0, TMDSType--1, ConnectorType-2
(II) fglrx(0): Connector0: DDCType-2, DACType-1, TMDSType-0, ConnectorType-3
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): DDC detected on DDCType 2 with Monitor Type 0
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) fglrx(0): I2C device "DDC:ddc2" removed.
(II) fglrx(0): DDC detected on DDCType 3 with Monitor Type 1
(II) fglrx(0): Primary head:
Monitor -- NONE
Connector -- DVI-I
DAC Type -- TVDAC/ExtDAC
TMDS Type -- Internal
DDC Type -- DVI_DDC
(II) fglrx(0): Secondary head:
Monitor -- CRT
Connector -- VGA
DAC Type -- Primary
TMDS Type -- NONE
DDC Type -- VGA_DDC
(II) fglrx(0): EDID data from the display on Secondary head ---------------------------
(II) fglrx(0): Manufacturer: GSM Model: 4366 Serial#: 62566
(II) fglrx(0): Year: 2004 Week: 2
(II) fglrx(0): EDID Version: 1.3
(II) fglrx(0): Analog Display Input, Input Voltage Level: 0.700/0.300 V
(II) fglrx(0): Signal levels configurable
(II) fglrx(0): Sync: Separate
(II) fglrx(0): Max H-Image Size [cm]: horiz.: 32 vert.: 24
(II) fglrx(0): Gamma: 2.81
(II) fglrx(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display
(II) fglrx(0): First detailed timing not preferred mode in violation of standard!(II) fglrx(0): redX: 0.636 redY: 0.327 greenX: 0.278 greenY: 0.600
(II) fglrx(0): blueX: 0.145 blueY: 0.064 whiteX: 0.283 whiteY: 0.298
(II) fglrx(0): Supported VESA Video Modes:
(II) fglrx(0): 720x400@70Hz
(II) fglrx(0): 720x400@88Hz
(II) fglrx(0): 640x480@60Hz
(II) fglrx(0): 640x480@67Hz
(II) fglrx(0): 640x480@72Hz
(II) fglrx(0): 640x480@75Hz
(II) fglrx(0): 800x600@56Hz
(II) fglrx(0): 800x600@60Hz
(II) fglrx(0): 800x600@72Hz
(II) fglrx(0): 800x600@75Hz
(II) fglrx(0): 832x624@75Hz
(II) fglrx(0): 1024x768@87Hz (interlaced)
(II) fglrx(0): 1024x768@60Hz
(II) fglrx(0): 1024x768@70Hz
(II) fglrx(0): 1024x768@75Hz
(II) fglrx(0): 1152x870@75Hz
(II) fglrx(0): Manufacturer's mask: 0
(II) fglrx(0): Supported Future Video Modes:
(II) fglrx(0): #0: hsize: 640 vsize 480 refresh: 75 vid: 20273
(II) fglrx(0): #1: hsize: 640 vsize 480 refresh: 85 vid: 22833
(II) fglrx(0): #2: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) fglrx(0): #3: hsize: 800 vsize 600 refresh: 85 vid: 22853
(II) fglrx(0): #4: hsize: 1024 vsize 768 refresh: 75 vid: 20321
(II) fglrx(0): #5: hsize: 1024 vsize 768 refresh: 85 vid: 22881
(II) fglrx(0): #6: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) fglrx(0): #7: hsize: 832 vsize 624 refresh: 75 vid: 20297
(II) fglrx(0): Supported additional Video Mode:
(II) fglrx(0): clock: 94.5 MHz Image Size: 310 x 230 mm
(II) fglrx(0): h_active: 1024 h_sync: 1072 h_sync_end 1168 h_blank_end 1376 h_border: 0
(II) fglrx(0): v_active: 768 v_sync: 769 v_sync_end 772 v_blanking: 808 v_border: 0
(II) fglrx(0): Ranges: V min: 50 V max: 160 Hz, H min: 30 H max: 71 kHz, PixClock max 110 MHz
(II) fglrx(0): Monitor name: T710BH
(II) fglrx(0): Monitor name:
(II) fglrx(0):
(II) fglrx(0): DesktopSetup 0x0000
(==) fglrx(0): PseudoColor visuals disabled
(==) fglrx(0): Overlay disabled
(**) fglrx(0): Overlay disabled
(II) fglrx(0): PLL parameters: rf=2700 rd=12 min=20000 max=40000
(==) fglrx(0): Using gamma correction (1.0, 1.0, 1.0)
(==) fglrx(0): Center Mode is disabled
(==) fglrx(0): TMDS coherent mode is enabled
(II) fglrx(0): Total 5 valid mode(s) found.
(--) fglrx(0): Virtual size is 1152x864 (pitch 1152)
(**) fglrx(0): *Default mode "1152x864": 108.0 MHz (scaled from 0.0 MHz), 67.5 kHz, 75.0 Hz
(II) fglrx(0): Modeline "1152x864" 108.00 1152 1216 1344 1600 864 865 868 900 +hsync +vsync
(**) fglrx(0): *Default mode "1024x768": 94.5 MHz (scaled from 0.0 MHz), 68.7 kHz, 85.0 Hz
(II) fglrx(0): Modeline "1024x768" 94.50 1024 1072 1168 1376 768 769 772 808
(**) fglrx(0): Default mode "832x624": 57.3 MHz (scaled from 0.0 MHz), 49.7 kHz, 74.6 Hz
(II) fglrx(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync
(**) fglrx(0): *Default mode "800x600": 56.3 MHz (scaled from 0.0 MHz), 53.7 kHz, 85.1 Hz
(II) fglrx(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) fglrx(0): *Default mode "640x480": 36.0 MHz (scaled from 0.0 MHz), 43.3 kHz, 85.0 Hz
(II) fglrx(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(--) fglrx(0): Display dimensions: (320, 240) mm
(--) fglrx(0): DPI set to (91, 91)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/lib/modules/libfb.a
(II) Module fb: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/lib/modules/libramdac.a
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.7
(**) fglrx(0): NoAccel = NO
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/lib/modules/libxaa.a
(II) Module xaa: vendor="X.Org Foundation"
compiled for 6.8.2, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.7
(==) fglrx(0): HPV inactive
(==) fglrx(0): FSAA enabled: NO
(==) fglrx(0): FSAA Gamma enabled
(==) fglrx(0): FSAA Multisample Position is fix
(**) fglrx(0): NoDRI = NO
(II) Loading sub module "fglrxdrm"
(II) LoadModule: "fglrxdrm"
(II) Loading /usr/lib/modules/linux/libfglrxdrm.a
(II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
compiled for 4.3.99.902, module version = 8.8.25
ABI class: X.Org Server Extension, version 0.2
(II) fglrx(0): Depth moves disabled by default
(**) fglrx(0): Capabilities: 0x00000000
(==) fglrx(0): cpuFlags: 0x4000000f
(==) fglrx(0): cpuSpeedMHz: 0x0000079d
(==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
(==) fglrx(0): UseFastTLS=0
(==) fglrx(0): BlockSignalsOnLock=1
(==) fglrx(0): EnablePrivateBackZ = NO
(--) Depth 24 pixmap format is 32 bpp
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B]
[1] 0 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xdffffe00 - 0xdffffeff (0x100) MX[B]
[8] -1 0 0xdfffff00 - 0xdfffffff (0x100) MX[B]
[9] -1 0 0xe0000000 - 0xdfffffff (0x0) MX[B]O
[10] -1 0 0xdfee0000 - 0xdfeeffff (0x10000) MX[B](B)
[11] -1 0 0xc8000000 - 0xcfffffff (0x8000000) MX[B](B)
[12] -1 0 0xdfec0000 - 0xdfedffff (0x20000) MX[B](B)
[13] -1 0 0xdfef0000 - 0xdfefffff (0x10000) MX[B](B)
[14] -1 0 0xd0000000 - 0xd7ffffff (0x8000000) MX[B](B)
[15] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[16] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[17] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[18] 0 0 0x0000c800 - 0x0000c8ff (0x100) IX[B]
[19] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[20] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[21] -1 0 0x0000dc00 - 0x0000dcff (0x100) IX[B]
[22] -1 0 0x0000fc00 - 0x0000fc0f (0x10) IX[B]
[23] -1 0 0x0000e800 - 0x0000e81f (0x20) IX[B]
[24] -1 0 0x0000e400 - 0x0000e41f (0x20) IX[B]
[25] -1 0 0x0000e000 - 0x0000e01f (0x20) IX[B]
[26] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[27] -1 0 0x0000c800 - 0x0000c8ff (0x100) IX[B](B)
[28] 0 0 0x000003b0 - 0x000003bb (0xc) IS[B]
[29] 0 0 0x000003c0 - 0x000003df (0x20) IS[B]
(II) fglrx(0): UMM area: 0xd05cd000 (size=0x07a33000)
(II) fglrx(0): driver needs XFree86 version: 4.3.x
(WW) fglrx(0): could not detect XFree86 version (query_status=-3)
(II) Loading extension ATIFGLRXDRI
(II) fglrx(0): doing DRIScreenInit
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (Unknown error 999)
drmOpenDevice: open result is -1, (Unknown error 999)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
drmOpenDevice: open result is -1, (Unknown error 999)
drmOpenDevice: open result is -1, (Unknown error 999)
drmOpenDevice: Open failed
[drm] failed to load kernel module "fglrx"
(II) fglrx(0): [drm] drmOpen failed
(EE) fglrx(0): DRIScreenInit failed!
(WW) fglrx(0): ***********************************************
(WW) fglrx(0): * DRI initialization failed! *
(WW) fglrx(0): * (maybe driver kernel module missing or bad) *
(WW) fglrx(0): * 2D acceleraton available (MMIO) *
(WW) fglrx(0): * no 3D acceleration available *
(WW) fglrx(0): ********************************************* *
(II) fglrx(0): FBADPhys: 0xd0000000 FBMappedSize: 0x08000000
(==) fglrx(0): Write-combining range (0xd0000000,0x8000000)
(II) fglrx(0): FBMM initialized for area (0,0)-(1152,8191)
(II) fglrx(0): FBMM auto alloc for area (0,0)-(1152,864) (front color buffer - assumption)
(==) fglrx(0): Backing store disabled
(==) fglrx(0): Silken mouse enabled
(II) fglrx(0): Using hardware cursor (scanline 864)
(II) fglrx(0): Largest offscreen area available: 1152 x 7323
(II) fglrx(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
Solid Horizontal and Vertical Lines
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128

[..::Ozzy::..]

do /etc/modules.autuload.d/kernel-2.6 jsem pridal

# /etc/modules.autoload.d/kernel-2.6:  kernel modules to load when system boots.
# $Header: /home/cvsroot/gentoo-src/rc-scripts/etc/modules.autoload.d/kernel-2.6,v 1.1 2003/07/16 18:13:45 azarah Exp $
#
# Note that this file is for 2.6 kernels.
#
# Add the names of modules that you'd like to load when the system
# starts into this file, one per line.  Comments begin with # and
# are ignored.  Read man modules.autoload for additional details.

# For example:
# 3c59ox
fglrx

ale pri bootu mi to nechce ten modul natahnout

ani lsmod mi nic neukaze

bash-2.05b$ lsmod
Module                  Size  Used by

[Gargamel]

[drm] failed to load kernel module "fglrx"

Problem je v tom, ze nemas natazeny modul v jadre. Z vypisu lsmod vyplyva, ze nemas ani v jadre zkompilovanou podporu pro moduly (prazdny vypis je hodne neobvykly) - pokud teda nemas narvane vsechny ovladace v jadre, coz je taky velka chyba.

Zkus si natahnout ten modul rucne a zkontroluj logy, mel by tam byt napsany duvod, proc se ti to nenatahlo. Vetsinou zlobi agpgart a DRI ovladac radeon.

[..::Ozzy::..]

Postupoval jsem podle tohoto nastaveni jadra
* Loadable module support -> Enable loadable module support: ENABLED
* Loadable module support -> Module unloading: ENABLED
* Loadable module support -> Automatic kernel module loading: ENABLED
* File systems -> Pseudo filesystems -> Virtual memory file system support: ENABLED
* Processor type and features -> MTRR (Memory Type Range Register) support:ENABLED
* Device drivers -> Character Devices -> /dev/agpgart (AGP Support): ENABLED
* Device drivers -> Character Devices -> (pick the correct AGP chipset option from the list, depending on your motherboard): ENABLED OR MODULE
Motherboard: VIA KT266/333/400 based ---- VIA chipset support
* Device drivers -> Character Devices -> Direct Rendering Manager (XFree86 4.1.0 and higher DRI support): DISABLED

OzzyTux ozzy # modprobe fglrx
FATAL: Module fglrx not found.

vubec tomu nerozumim.. vzdyt jsem ty ovladace emergnul a updatoval opengl pro ati
uz jsem zkousel nekolik postupu podle googlu a vše neúspěšné... začínám z toho být
celkem frustrovaný a nervózní

[Gargamel]

Klid, to chce cvik...

Nemas zkompilovany modul fglrx - pri emergovani balicku ati-drivers by se to melo automaticky zkompilovat. Bud tam byly nejake chyby, nebo nemas spravne symlink /usr/src/linux na aktualni jadro. S tim jadrem do ktereho se to kompiluje pak nemusis nic delat, melo by to po dokonceni emerge normalne fungovat a modul by pak mel jit natahnout.

[..::Ozzy::..]

kdyz jsem emergoval znova ati-drivers
tak tam skocila nejakek warning ze se nezkompilovali DRM modules

bash-2.05b# emerge ati-drivers
Calculating dependencies ...done!
>>> emerge (1 of 1) media-video/ati-drivers-8.8.25 to /
>>> md5 src_uri ;-) fglrx_6_8_0-8.8.25-1.i386.rpm
 * Determining the location of the kernel source code
 * Found kernel source directory:
 *     /usr/src/linux
 * Found sources for kernel version:
 *     2.6.11-gentoo-r3
 * X11 implementation is xorg-x11.
>>> Unpacking source...
>>> Unpacking fglrx_6_8_0-8.8.25-1.i386.rpm
 * Applying 8.08-kernel-2.6.10.patch ...                                  [ ok ]
>>> Source unpacked.
 * Building the DRM module...
make: Entering directory `/usr/src/linux-2.6.11-gentoo-r3'
  CC [M]  /var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agp3.o
  CC [M]  /var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/nvidia-agp.o
  CC [M]  /var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.o
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c: In function `x86_64_insert_memory':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c:3804: warning: integer constant is too large for "long" type
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c: In function `agp_find_supported_device':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c:6527: warning: unused variable `cap_ptr'
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c: In function `__fgl_agp_init':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c:7612: warning: `pm_register' is deprecated (declared at include/linux/pm.h:106)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c: In function `__fgl_agp_cleanup':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c:7622: warning: `pm_unregister_all' is deprecated (declared at include/linux/pm.h:116)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c: At top level:
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/agpgart_be.c:6508: warning: `agp_check_supported_device' defined but not used
  CC [M]  /var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/i7505-agp.o
  CC [M]  /var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.o
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `firegl_stub_putminor':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:504: warning: `inter_module_put' is deprecated (declared at include/linux/module.h:578)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:506: warning: `inter_module_unregister' is deprecated (declared at include/linux/module.h:574)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `firegl_stub_register':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:526: warning: `inter_module_register' is deprecated (declared at include/linux/module.h:573)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:557: warning: `inter_module_put' is deprecated (declared at include/linux/module.h:578)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_get_vm_phys_addr':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:1579: warning: passing arg 1 of `pmd_offset' from incompatible pointer type
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `do_vm_shm_nopage':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2074: warning: passing arg 1 of `pmd_offset' from incompatible pointer type
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_vm_phys_addr_str':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2445: warning: passing arg 1 of `pmd_offset' from incompatible pointer type
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: At top level:
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2533: warning: initialization from incompatible pointer type
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_vm_map':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2594: warning: implicit declaration of function `remap_page_range'
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: At top level:
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2748: error: parse error before '*' token
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2748: warning: type defaults to `int' in declaration of `drm_agp_module_stub'
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2748: warning: data definition has no type or storage class
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agpgart_available':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2890: error: `drm_agp_t' undeclared (first use in this function)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2890: error: (Each undeclared identifier is reported only once
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2890: error: for each function it appears in.)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2890: error: parse error before ')' token
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2911: error: request for member `free_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2913: error: request for member `free_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2916: error: request for member `allocate_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2918: error: request for member `allocate_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2921: error: request for member `bind_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2923: error: request for member `bind_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2926: error: request for member `unbind_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2928: error: request for member `unbind_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2931: error: request for member `enable' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2933: error: request for member `enable' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2936: error: request for member `acquire' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2938: error: request for member `acquire' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2941: error: request for member `release' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2943: error: request for member `release' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2946: error: request for member `copy_info' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:2948: error: request for member `copy_info' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_uninit':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3019: warning: `inter_module_put' is deprecated (declared at include/linux/module.h:578)
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_free_memory':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3052: error: request for member `free_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3053: error: request for member `free_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_allocate_memory':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3062: error: request for member `allocate_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3063: error: request for member `allocate_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_bind_memory':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3073: error: request for member `bind_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3074: error: request for member `bind_memory' in something not a structureor union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_unbind_memory':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3084: error: request for member `unbind_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3085: error: request for member `unbind_memory' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_enable':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3095: error: request for member `enable' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3097: error: request for member `enable' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_acquire':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3143: error: request for member `acquire' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3144: error: request for member `acquire' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_release':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3154: error: request for member `release' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3155: error: request for member `release' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c: In function `__ke_agp_copy_info':
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3168: error: request for member `copy_info' in something not a structure or union
/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.c:3175: error: request for member `copy_info' in something not a structure or union
make[1]: *** 

[/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.o] Error 1
make: *** [_module_/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod] Error 2
make: Leaving directory `/usr/src/linux-2.6.11-gentoo-r3'

>>> Test phase [not enabled]: media-video/ati-drivers-8.8.25

>>> Install ati-drivers-8.8.25 into /var/tmp/portage/ati-drivers-8.8.25/image/ category media-video
install: cannot stat `/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/fglrx.ko': No such file or directory
 * lib -> lib
man:
making executable: /usr/lib/libfglrx_gamma.so.1.0
>>> Completed installing ati-drivers-8.8.25 into /var/tmp/portage/ati-drivers-8.8.25/image/

>>> Merging media-video/ati-drivers-8.8.25 to /
--- /etc/
--- /etc/env.d/
>>> /etc/env.d/09ati
--- /lib/
--- /lib/modules/

--- /lib/modules/2.6.11-gentoo-r3/
--- /lib/modules/2.6.11-gentoo-r3/video/
--- /opt/
--- /opt/ati/
--- /opt/ati/bin/
>>> /opt/ati/bin/fglrxinfo
>>> /opt/ati/bin/fglrx_xgamma
>>> /opt/ati/bin/fglrxconfig
--- /usr/
--- /usr/lib/
--- /usr/lib/modules/
--- /usr/lib/modules/dri/
>>> /usr/lib/modules/dri/fglrx_dri.so
--- /usr/lib/modules/linux/
>>> /usr/lib/modules/linux/libfglrxdrm.a
--- /usr/lib/modules/drivers/
>>> /usr/lib/modules/drivers/fglrx_drv.o
--- /usr/lib/opengl/
--- /usr/lib/opengl/ati/
>>> /usr/lib/opengl/ati/lib/
>>> /usr/lib/opengl/ati/lib/libGL.so.1.2
>>> /usr/lib/opengl/ati/lib/libGL.la
>>> /usr/lib/opengl/ati/lib/libGL.so -> libGL.so.1.2
>>> /usr/lib/opengl/ati/extensions -> ../xorg-x11/extensions
>>> /usr/lib/opengl/ati/include -> ../xorg-x11/include
>>> /usr/lib/libfglrx_gamma.so.1.0
>>> /usr/lib/libfglrx_gamma.a
--- /usr/include/
--- /usr/include/X11/
--- /usr/include/X11/extensions/
>>> /usr/include/X11/extensions/fglrx_gamma.h
--- /usr/include/include/
--- /usr/include/include/GL/
>>> /usr/include/include/GL/glxATI.h
>>> /usr/lib/opengl/ati/lib/libGL.so.1 -> libGL.so.1.2
>>> Safely unmerging already-installed instance...
--- !mtime obj /usr/lib/opengl/ati/lib/libGL.so.1.2
--- !mtime obj /usr/lib/opengl/ati/lib/libGL.la
--- !mtime obj /usr/lib/modules/linux/libfglrxdrm.a
--- !mtime obj /usr/lib/modules/drivers/fglrx_drv.o
--- !mtime obj /usr/lib/modules/dri/fglrx_dri.so
--- !mtime obj /usr/lib/libfglrx_gamma.so.1.0
--- !mtime obj /usr/lib/libfglrx_gamma.a
--- !mtime obj /usr/include/include/GL/glxATI.h
--- !mtime obj /usr/include/X11/extensions/fglrx_gamma.h
--- !mtime obj /opt/ati/bin/fglrxinfo
--- !mtime obj /opt/ati/bin/fglrxconfig
--- !mtime obj /opt/ati/bin/fglrx_xgamma
--- cfgpro dir /lib/modules/2.6.11-gentoo-r3/video
--- cfgpro dir /lib/modules/2.6.11-gentoo-r3
--- !mtime obj /etc/env.d/09ati
--- !empty dir /usr/lib/opengl/ati/lib
--- !empty dir /usr/lib/opengl/ati
--- !empty dir /usr/lib/opengl
--- !empty dir /usr/lib/modules/linux
--- !empty dir /usr/lib/modules/drivers
--- !empty dir /usr/lib/modules/dri
--- !empty dir /usr/lib/modules
--- !empty dir /usr/lib
--- !empty dir /usr/include/include/GL
--- !empty dir /usr/include/include
--- !empty dir /usr/include/X11/extensions
--- !empty dir /usr/include/X11
--- !empty dir /usr/include
--- !empty dir /usr
--- !empty dir /opt/ati/bin
--- !empty dir /opt/ati
--- !empty dir /opt
--- !empty dir /lib/modules
--- !empty dir /lib
--- !empty dir /etc/env.d
--- !empty dir /etc
--- !targe sym /usr/lib/opengl/ati/lib/libGL.so.1
--- !targe sym /usr/lib/opengl/ati/lib/libGL.so
--- !targe sym /usr/lib/opengl/ati/include
--- !targe sym /usr/lib/opengl/ati/extensions
>>> original instance of package unmerged safely.

 * To switch to ATI OpenGL, run "opengl-update ati"
 * To change your XF86Config you can use the bundled "fglrxconfig"

 * ***
 * If you are experiencing problems with memory allocation try to add
 * this line to in your X11 configuration file:
 *              Option "KernelModuleParm"  "agplock=0"
 * That should solve the hangups you could have with Neverwinter Nights
 * ***

[/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod/firegl_public.o] Error 1
make: *** [_module_/var/tmp/portage/ati-drivers-8.8.25/work/lib/modules/fglrx/build_mod] Error 2
make: Leaving directory `/usr/src/linux-2.6.11-gentoo-r3'

>>> Test phase [not enabled]: media-video/ati-drivers-8.8.25

[Gargamel]

To vypada na uplne beznou nekompatibilitu fglrx a novejsich verzi kernelu. Zkus se mrknout na gentoo fora (forums.gentoo.org), tam se tyhle problemy omylaly tisickrat a pro kazdou verzi kernelu bys mel najit kratky patch.

Tyhle problemy jsou u fglrx uplne bezne (ale i u nVidiackych binarnich ovladacu), je to dan za rychly vyvoj a nekvalitni vyvojove tymy HW firem.

[..::Ozzy::..]

dik za info.. kouknu na to forum a pak dam kdyztak sem vedet

[..::Ozzy::..]

Takze jsi mel pravdu je to tim ze ovladace ati-drivers-8.8.25
jsou s timhle jadrem nekompatibilni

tak jsem nasel na foru gentoo tri radky prikazu a po jejich zapisu vse jede jak ma

mkdir -p /etc/portage
echo "media-video/ati-drivers ~x86" >> /etc/portage/package.keywords
emerge ati-drivers

..
je to tim ze se budou stahovat novejsi ovladace ati-drivers-8.10.19


jeste jednou dik za rady Gargamel

ted jsem zas o neco chytrejsi

[Gargamel]

Aha no to jsem si nevsiml, ze pouzivas stable vetev. V tomhle pripade je doporuceno pouzivat unstable balicky ovladacu...

[Dr Meduza]

proc pouzivas taky stary ovladace?
je na nich neco lepsiho nez na 8.12.10?

[..::Ozzy::..]

kdyz jsem nepouzil vyse uvedene tri radky tak sem mi stahovali dokonce 8.8.5
a ty jsou nekompatibiln9

zacali se stahovat 8.10.19 tak jsem je tam dal... a chodi to a to me pro dnesek
staci... po tech dvou dnech co jsem se s tim trapil..

[Gargamel]

staci... po tech dvou dnech co jsem se s tim trapil..

No vidis, to bud rad, ze ti to jede. Tyhle ovladace totiz na R9250 a nizsich nepodporuji pod Linuxem DVI vystup - uzasna feature, ktera driv fungovala.

[hwsoft]

staci... po tech dvou dnech co jsem se s tim trapil..

No vidis, to bud rad, ze ti to jede. Tyhle ovladace totiz na R9250 a nizsich nepodporuji pod Linuxem DVI vystup - uzasna feature, ktera driv fungovala.

je k tomu nekde nejaky info? Nejak nemuzu najit, a to ze mi nejede DVI me dost stve.

[Gargamel]

No vidis, to bud rad, ze ti to jede. Tyhle ovladace totiz na R9250 a nizsich nepodporuji pod Linuxem DVI vystup - uzasna feature, ktera driv fungovala.

je k tomu nekde nejaky info? Nejak nemuzu najit, a to ze mi nejede DVI me dost stve.

Obavam se, ze jenom poznamka, ze je to nejaky bug a kopa bugreportu. Hodne lidi si na to uz stezovalo, resenim je pouzivat DRI drivery, ktere jedou bez problemu i ve 3D na techto starsich kartach. Na DX9 kartach zase nejede DRI a mely by jet fglrx drivery.

[Airwolf]

Jak je to s Gentoo 2006.1 ? ati-drivers-8.28.8 hlasi pri emerge cannot stat 'fglrx.ko':no such file or directory
ja uz nevim jak se s tim porvat, novejsi ovladace nejsou, samotny gentoo bezi od vcerejska, na forech jsem zatim funknci reseni nenasel...

[Gargamel]

Jak je to s Gentoo 2006.1 ? ati-drivers-8.28.8 hlasi pri emerge cannot stat 'fglrx.ko':no such file or directory
ja uz nevim jak se s tim porvat, novejsi ovladace nejsou, samotny gentoo bezi od vcerejska, na forech jsem zatim funknci reseni nenasel...

Jedu na tom uz vic nez rok a nemam problem. Pri instalaci ebuildu se kompiluje modul do jadra, tak se ujisti, ze mas spravny /usr/src/linux symlink a funkcni jadro v nem. Doporucuju sledovat hlasky emerge