-
Zapojení svítivých LED
Zdravím, mohl by mě někdo poradit jak zapojit cca 4 LEDky na počitáčový zdroj, konkrétně uvažuju asi na 5V větev napájení HDD? LEDka by měla být asi některá z těchto:
511-444 L-EP2036-150BW1 vysoce svítivá LED, bílá, 3,4V/150mA, 7000°K, vyzařovací úhel 30°, svítivost 5cd, (světelný tok 4lm)
511-445 L-EP2012-150BW1 vysoce svítivá LED, bílá, 3,4V/150mA, 7000°K, vyzařovací úhel 10°, svítivost 20cd, (světelný tok 4lm)
511-446 L-EP204K-150BW1 vysoce svítivá LED, bílá, 3,4V/150mA, 7000°K, vyzařovací úhel 100°, svítivost 1,5cd, (světelný tok 4lm)
Jde mě o schéma zapojení a součástky co budu potřebovat. Je mi jasný že ten zdroj (AT) budu muset ještě něčím zatížit aby jel, to není problém. POkud by šlo udělat zapojení s regulací svítivosti (jde to vůbec u LED?) bylo by to ještě lepší. Asi je to dost primitivní věc ale co se týče elektriky tak su úplná LAMA, tak mě nekamenujte. Dík
-
-
Díky moc, myslím že z těch odkazů sem to pochopil i já.
-
Mohu dotaz , pokud mám dostatečný napětí , je lepší je zapojit seriově nebo paralelně ? nebo je to jedno - co se týče použití v pc (12V větev utáhne 3 nebo 4 dioty , to mi stačí)
edit
Tak asi seriově co , páč pak ten rezistor míň topí, že ?
-
Citace:
Původně odeslal Erda
Mohu dotaz , pokud mám dostatečný napětí , je lepší je zapojit seriově nebo paralelně ? nebo je to jedno - co se týče použití v pc (12V větev utáhne 3 nebo 4 dioty , to mi stačí)
edit
Tak asi seriově co , páč pak ten rezistor míň topí, že ?
Asi tak. (tvoja úvaha je správna) :wink:
-
Citace:
Původně odeslal Erda
Mohu dotaz , pokud mám dostatečný napětí , je lepší je zapojit seriově nebo paralelně ? nebo je to jedno - co se týče použití v pc (12V větev utáhne 3 nebo 4 dioty , to mi stačí)
edit
Tak asi seriově co , páč pak ten rezistor míň topí, že ?
to taky a navíc se vyhneš problému v případě, že tvoje LED nebudou mít zcela stejné parametry, což by se u paralelního řazení projevilo v nerovnoměrném rozdělení proudu mezi jednotlivé LED a tedy i v nestejné svítivosti.
Tento problém odpadá při sériovém žazení, protože tam je nutně proud všemi diodami stejný.
-
No záleží jesli mají diody stejný pracovní bod, tedy optimální svítivost/proud, jesli ne, tak by bylo lepší paralelní zapojení, ovšem s podmínkou, že každá dioda bude mít vlastní resistor.
-
no, já jsem reagoval na možnost, když diody spojené paralelně budou mít společný rezistor, jak to bylo v jednom z linků výše.
Samostatný rezistor pro každou diodu je o něčem jiném, to je košer
I kdyby byly diody se shodnou charakteristikou (jako že asi nebudou zcela shodné), pak kromě napájení malým napětím je výhodnější spojení do serie.
Diody stejného typu z téže výrobní serie by neměly dělat problem ani při spojení paralelně.
-
Citace:
Původně odeslal Miuvek
Diody stejného typu z téže výrobní serie by neměly dělat problem ani při spojení paralelně.
Rekneme ze ne, ale vsichni je davaji do serie, i za cenu ze musi stepup menic. A proc?
- Svitivivost primo zavisi na proudu (stabilizace pracovniho bodu, se lepe dela ze zdroje proudu nez ze zdroje napeti)
energeticky je vyhodnejsi je radit do serie
-
nj, dyť jsem psal, že zapojení do serie je více košer...
-
ještě jeden dotaz stran zapojení LED:
je nutné při zapojení LED LUXEON na 12 V dodržet výkon 1,2W nebo stačí dodržet 350 mA?
-
Re: Zapojení svítivých LED
350 mA je maximum!
Nastav radši menší proud.
min. odpor tedy bude 12 - 4 = 8 , 8 : 0,350 = 22,8 Ohmů , ale dal bych tam
větší tak 27 Ohmů na na 3 Waty
(platí pro jednu diodu v sérii s odporem)
-
Re: Zapojení svítivých LED
Jen mám obavu, abych to neupekl, protože na 12 V to dá při povoleným proudu 350 mA výkon 4 W a tabulkově to má jen 1,2 W
chci si vyrobit- vlasně už leží na stole SNAKE dvojče,mám na to specielní použití.Mělo by to vydržet několik hodin.
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal Kall
Jen mám obavu, abych to neupekl, protože na 12 V to dá při povoleným proudu 350 mA výkon 4 W a tabulkově to má jen 1,2 W
chci si vyrobit- vlasně už leží na stole SNAKE dvojče,mám na to specielní použití.Mělo by to vydržet několik hodin.
Já to počítám asi jinak , úbytek na diodě je 4V a proud 350 mA to je 1,4W.
Odpor dej dál od diody, tomu to nevadí měl by být min.na 3W
-
Re: Zapojení svítivých LED
Jde o to ze u LED je stanoven jake je jeji napajeci napeti pri kterem si odebere uvedeny proud, tzn i uvedeny vykon. Takze ma-li byt LED na 4V pri kterych odebira uvedenych 350mA a chci to pripojit na 12V, tak jak jiz bylo uvedeno spocitam si odpor, na kterem zustane napeti 12V-4V=8V pri protekajicim proudu 350mA, coz je jiz uvedenych 22,8 ohmu a v tabulkach je bezne k sehnani bud 22 ohmu nebo spise 27 ohmu aby se dodrzely povolene hodnoty. A vykon odporu spocitam jako P=R*I^2, coz je pri odporu 22,8 ohmu nejakych 2,7W no a k sehnani je bud treba dat dva 2W nebo jeden 5W.
-
Re: Zapojení svítivých LED
Díky za informace, jsem jen amater.
-
Re: Zapojení svítivých LED
Ahoj,
nevyštrachal by jste někdo nějaké jednoduché zapojení red/green LED na 220V ?
viděl jsem to někde (Conrad?) jako modul stavebnice, jsou tam asi 3 součástky, ale nikde to nemůžu najít a dávat za to kilo + dobírka se mi nějak nechce...
-
Re: Zapojení svítivých LED
Easy, spocitej si kapacitu kondenzatoru a zapoj ho do serie s diodou. Neni nic jednodussiho, ale nezapomen to odizolovat, at te to nekopne.
Jinak Z = 1/(2πfC), kde f = 50, C je ta kapacita, Z spocitas z max proudu co zvladne ta dioda a napeti (230V).
Pro beznou diodu (30mA) ti vyjde Z = U/I = 7666Ω takze 7666*2*3.14*50 = 1/C ... C = 415nF
Kdyz das mensi kondik (400n) bude vetsi impedance a tim padem mensi proud.
-
Re: Zapojení svítivých LED
uau, to jako jenom kondik, nic jinyho? A zalezi na tom jakej (keramika, slida,..) ?
Izolovany to bude v pohode, ale jsem bohuzel vyucenej strojar, elektro me nic nerika tak sorry mozna za uplne blbou otazku :-/
-
Re: Zapojení svítivých LED
Ma matrosi nezalezi, hlavne musi bejt na dost velky napeti (400V). Tyhle maly kapacity jsou ovsem vetsinou OK, horsi je to pak s elitama, tam uz sou obrovsky tolerance, problemy s polaritou ...
Vyzkousej, maximalne ti zdechne dioda + kondik za 5Kc ;).
-
Re: Zapojení svítivých LED
Jenom takovy maly detail, nemel by ten condr byt na AC napajeni, protoze klasickej je na DC a myslim si ,ze by nevydrzel tu zapornou vetev napeti ze site.?
-
Re: Zapojení svítivých LED
Tohle plati u elitu, u malejch kondiku (keramika, slida, ...) neni zadna polarita.
-
Re: Zapojení svítivých LED
kondik v serii s ledkou sice funguje, ale ne uplne korektne - paralelne ke kondiku doporucuju dat odpor 1M a paralelne k ledce obyc kremikovou diodu, polovanou opacne nez ledka (jako ochranu ledky) ... a nebo dalsi ledku misto diody ... jo, a kondik doporucuju svitkovej, polystyrenovej, a radsi na 630V (protoze 230x3^(-1) je prave tech 400 a pokud bude v siti spicka, kondik nemusi vydrzet)
EDIT: http://www.belza.cz/ac-led/kontrol.htm
-
Re: Zapojení svítivých LED
Panove diky moc, vycerpavajici odpovedi.
Jestli se uz neozvu, nekde jsem zapomnel na izolaci :-)
-
Re: Zapojení svítivých LED
Posledni veta pred smrti: Pustte mne k tomu ja jsem elektrikar, tento vodic je urcite nulak :)
Tak hodne zdaru. Jo a ten kondr radeji opravdu na 630V, protoze kdyz pracuje na hranici sveho napeti tak rychleji ztraci svou kapacitu.
-
Re: Zapojení svítivých LED
Pokud toto zapojení připojíte k napětí při jeho maximální hodnotě (asi 325V), jaký bude proud diodou? Nejsem si jistý, zda povolené proudové pulsy jsou u LED diod stejné jako u plošných usměrňovacích diod. Asi bych životnosti takové diody moc nevěřil.
-
Re: Zapojení svítivých LED
Tak jsem tady zas s trochu jiným problémem. Myslím že k tématu, tak nebudu zakládat další vlákno..
Začal jsem řešit intimní osvětlení v pracovně (k PC/sledování TV/...) a s úspěchem mám vyzkoušen 1W Luxeon. Teď bych rád přešel od pokusů k praktické realizaci, tj. osvětlení pracovní plochy, podhledové osvětlení pokoje (mimochodem tohle mám odkoukáno z hotelu v Tunisu a je to bomba), a pravděpodobně to budu chtít roztáhat i do dalších místností.
Zapojení musí být 100% paralelní (kvůli možnosti vypínání jednotlivých LED), provozní napětí/max. proud a výpočet srážecího odporu jsou jasné, to jsem si už našel jinde.
Největší problém vidím u zdroje. Budu potřebovat něco, co mi dokáže dát cca 0,3-5A podle počtu zapnutých zdrojů. Představoval bych si něco, co nebude zbytečně točit elektroměr naprázdno (jinak se nemusím namáhat s LEDkama..), bude naprosto tiché a ideálně při vypnutí všech světel bude mít i skoro nulovou spotřebu...
PC zdroj se bez zátěže nerozjede a chce ofuk, ale zase by byl "zadarmo".
Klasika trafo do zásuvky je sice nejlevnější, ale s efektivita bude nejspíš dost špatná.
Nebo koupit průmyslový spínaný zdroj (něco sem zahlídl v GME kolem 600,-) ?
-
Re: Zapojení svítivých LED
Heh, transformator je nejucinejsi stroj kterej lidstvo zna, v pripade velkyho trafa se da dostat i pres 99%. Bezny domaci maj kolem 80%, zalezi predevsim na materialu jadra.
Pokud ti ale z nejakyho duvodu nejde o bezpecnost, zadny trafo nepotrebujes. LEDky muzes klidne zapojit primo(mineno primo do rozvodu 230V), do serie s kondenzatorem. Ztratovej vykon minimalni.
-
Re: Zapojení svítivých LED
No nejsem zadnej guru na elektro, ale co si pamatuju ze skoly, tak u normalniho trafa to velka slava nebyla. Ostatne proto existuji spinany zdroje (ano, je tam taky trafo) a nenapajime PC adapterem ze zasuvky. Ale nechci se hadat - jen uvadim z ceho prameni moje presvedceni o tom co jsem napsal.
O bezpecnost mi samozrejme jde, uz kvuli nasemu prckovi, pred kterym za chvili nebude bezpecne vubec nic. Planuju tam i nejakou zkratovou pojistku.
Takze mam vzit klasickej zasuvkovej adapter ???
Pokud nevymyslim neco chytryho na samovypinani, tak pojede nonstop, tak me spotreba "naprazdno" celkem zajima.
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal
Aigor
No nejsem zadnej guru na elektro, ale co si pamatuju ze skoly, tak u normalniho trafa to velka slava nebyla. Ostatne proto existuji spinany zdroje (ano, je tam taky trafo) a nenapajime PC adapterem ze zasuvky.
Pokud se nepletu, tak spínaný zdroje existujou hlavně protože na napájení pc bys potřeboval trafo větší než je celej case a vážící 100+ kilo:D. Spínaný zdroj dělá vlastně to, že převádí 50Hz elektřinu na mnohonásobně vyšší frekvenci, čím vyšší frekvence, tím menší trafo je potřeba.
-
Re: Zapojení svítivých LED
OK, nechám se poučit.
Zdrojů s proudem >2A moc není, co tenhle MW 12V/5A4 ?
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal
Peca-on-line
Pokud se nepletu, tak spínaný zdroje existujou hlavně protože na napájení pc bys potřeboval trafo větší než je celej case a vážící 100+ kilo:D. Spínaný zdroj dělá vlastně to, že převádí 50Hz elektřinu na mnohonásobně vyšší frekvenci, čím vyšší frekvence, tím menší trafo je potřeba.
jj, presne tak, trafo ktery by dalo ty desitky/stovky A by muselo mit i odpovidajicne dimenzovany draty - to co je normalne v zasuvce je tusim 1,5ka a bezne se bere tak 10A/mm2.
Citace:
Původně odeslal
Aigor
Nikde tam neni napsany, jestli to dava stejnosmerne (asi jo), to je pro tebe nevyhodny, lepsi je pouzit stridavej zdroj, prave proto, ze nemusis pouzivat odpory, ale nahradis je kondenzatorama, ktery se na stridavym rozvodu chovaji jako odpor. Dal to spocitas uz jako s odporem, zapojuje se do serie s diodou. Cim mensi kapacita, tim vetsi odpor.
Pr: mam diodu s maximalnim proudem 30mA, kterou pripojuju na 24V/50Hz.
R= U/I = 24/0,03 = 800Ω => potrebuju kondenzator, ktere ma maximalne 4µF
Je treba samo vybrat kondenzator, kterymu stridavy napeti nevadi => ne bezny elektrolity.
Jinak se poohlidni spis po necem jinym, tohle sou veci delany na trvalej provoz. Muzes jich mit vic.
Nemam predstavu, kde si vzal tech 5A, pri bezny spotrebe diody 20mA to dava cca 250 diod. Pri cca 2,5V je to 12,5W. Prikon je z hlediska trafa zajimavejsi nez proud. Protoze vetsi napeti na vystupu = mensi proud a mensi trafo. Ten odkaz vede na trafa, ktery by ti mely stacit.
-
Re: Zapojení svítivých LED
No píšou že je to stabilizovaný zdroj, takže to bude určitě ss. Co se týká použití kondenzátorů, tomu nerozumím... resp. není mi moc jasné v čem je pro mě výhodnější použít kond místo rezistoru ??? Selská logika mě říká, že tu jednu součástku stejně neušetřím, navíc střídavý proud neumím stabilizovat... Kdyby s výkyvem napětí na zásuvkách poblikávaly LEDy, docela by mi to vadilo (nevím, třeba by to nebylo poznat), u nás to skáče kolem 30V.
Co se týká těch diod, jde jak sem psal o Luxeony. Tam je proud od 350mA do 700mA a výš na jednu LEDku. Při paralelním řazení to pak rychle naskáče.
-
Re: Zapojení svítivých LED
Tak to urcit neni jedna LEDka, to leda ze to uz sou cely sestavy. Odpory se ti narozdil od kondenzatoru hrejou a predevsim bys musel timenzovat odber i na ne, protoze ty odpory budou mit vetsi spotrebu nez ty LED. Navic pri takovym proudu co uvadis musis mit kurevsky velky odpory, to co se bezne prodava je 1/4 - 1W a na tomto by se takovej odpor vyparil. Resit kolisani napeti je u svetelnyho zdroje mimo.
-
Re: Zapojení svítivých LED
3W LED, bílé teplé světlo
LED 1W bílá
U toho zdroje vycházím z úvahy, že pokud budu srážet nízké napětí (např. 5V), tak se na tom odporu moc pálit nebude...? Jinak samozřejmě tyhle LEDky je potřeba chladit samotný, tak by to nebyl až takovej problém.
Co se týká kolísání napětí, tak např. při provozu na accu to vidět je dost a docela to ruší.
EDIT: Vyhrabal jsem ze zásob starší AT zdroj, 5V/20A bude na pokusy stačit.. Pak bych proměřil skutečnou spotřebu a ev. investoval peníze a čas na finální zdroj.
-
Re: Zapojení svítivých LED
Zdravím mezi svátky, zase jsem se chvíli dostal k páječce tak mám dvě možná přilouplé otázky..
1. Pokud připojuji LED na stejné napětí jaké mají provozní, musím to ještě nějak ošetřit, nebo ne?
Tj. např. zdroj 3V/2000mA přímo na LEDku pro 3V/20mA ???
2. Pro regulaci svitu LED je lepší použít nějaký obvod PWM nebo snížit napětí ? Předpokládám, že bych použil nějakou kontrukci pro regulaci větráků..
-
Re: Zapojení svítivých LED
LED diodu bys měl připojit na zdroj proudu a ne na zdroj napětí, stačí si nakreslit VA charakteristiku diody v propustném směru a bude ti to jasné.
-
Re: Zapojení svítivých LED
hmm a co to v praxi znamená? resp. nemohl bys mi to přeložit nějak srozumitelněji?
vycházím z toho, že pro napájení LEDky je potřeba rezistor, který srazí napětí na provozní. Podle rozdílu napětí se určí hodnota odporu. Pokud je rozdíl nulový, selská logika napovídá, že rezistor neni potřeba :-/ Proud si asi dioda vezme takový jaký potřebuje, tedy nejspíš takový co je uveden v katalogu. Pokud se pletu, tak mě opravte.
-
Re: Zapojení svítivých LED
Teoreticky ano,ale v praxi je to složitější.To napětí na diode kolísá s teplotou,ten zdroj má taky nějakou toleranci a vzhledem k poměrně strmé VA charakteristice LED diody desetina voltu zapříčiní to,že LED-kou nepoteče katalogových 20mA,ale třeba 50mA a to už dost podstatně zkrátí životnost LED-ky.Navíc i nepatrné kolísaní napětí zdroje způsobí velké kolísání svitu diody,kdy při napětí zdroje 2,9V dioda téměř nebude svítit a při napětí 3,1V už bude přetížená.
Proto je lepší použít zdroj proudu,který udržuje proud diodou bez ohledu na napětí na LED diodě.
-
Re: Zapojení svítivých LED
Přesně tak to je. Pro 007 jednu vodku a martini, protřepat, nemíchat. :-)
-
Re: Zapojení svítivých LED
007 - díky, z toho jsem to pochopil i já ;), K+
Jen už chvíli trápím strejdy googla a nedaří se mi nikde najít nějaký dostatečně okomentovaný a jednoduchý schémátko.
Buď obecný diskuse, nebo komerční moduly (další,...)
nevíte o něčem co bych zvládl vyrobit i amatér a nestálo to tolik ?
-
Re: Zapojení svítivých LED
Zkus se inspirovat tady http://belza.cz/ledlight/leds.htm popr. tady http://belza.cz/ledlight/minil.htm ... a nebo si rovnou projdi celou sekci Sviceni a blikani na http://belza.cz/ .
-
Re: Zapojení svítivých LED
Jednoduchý zdroj proudu je tady http://www.volny.cz/zelena.prisera/S..._regulator.gif ,je to katalogové zapojení LM317,napájecí napětí musí být asi o 3V větší než napětí LED diody (max 40V).Je to řešení jednoduché a levné,ale lineární a při velkém rozdílu napětí diody a zdroje se bude stablik hřát.Poměrně dokonalé obvody pro řízení LED diod vyrábí firma Maxim,ale cena a dostupnost je někde jinde.
-
Re: Zapojení svítivých LED
Díky oběma, poslední den jsem strávil hledáním na netu a na podobné zapojení s LM317 jsem už taky narazil. Vidím to jako optimální zapojení pro osvětlení prac. stolu.
Ale pokud bych chtěl co nejjednodušší zapojení, obětoval část výkonu LED a nekoukal na efektivitu, napájel ze stabil. adaptéru, tak když použiju sériový odpor a napětí nastavím o 0,5V míň než je předepsané, tak je to košér ne? Jen se chci ujistit, že to správně chápu.
K těm zdrojům konst. proudu - co je tak zázračnýho na krabičkách co prodává např. GME (Napájecí zdroje spínané pro LED LUXEON, že stojí 800-1.200 ?
Je to stejný princip, nebo v čem je to o tolik lepší ?
-
Re: Zapojení svítivých LED
Použil bych 5V stabilizovaný zdroj,ledky bych řadil paralelně a každá by měla svůj omezovací odpor.Pro běžnou bílou nebo modrou ledku (3,6V/20mA)by to byl odpor 5V-3,6V/0,02A=70ohm.Na odporu bude výkonová stráta 1,4V*0,02A=0,028W takže běžnej čtvrtwatovej odpor se ani neohřeje.
-
1 Příloh-a(y)
Re: Zapojení svítivých LED
Dovolím si trošku opakování a menší shrnutí. Podle výše uvedných návodů jsem si postavil zdroj proudu podle přiloženýho schématu. Je to naprosto primitivní zapojení i pro začátečníka jako já, můžete si to sdrátovat i bez plošňáku a součástky pořídíte asi za půlku piva ;)
Zapojení je optimální hlavně pro výkonové LED (350/700mA), kde si potřebnou hodnotu odporu spočítáte vzorečkem R = 1,25 / I
Stabilizátor LM317 topí prakticky jen pokud musí hodně snižovat napětí, např. klasický Luxeon při 350mA má napětí kolem 3,5V. Při napájení obvodu 5-6V bude stabilizátor prakticky studený a obejdete se bez chladiče.
Velkou výhodou je sériové řazení LED, které nepotřebují další součástky (žádné srážecí odpory) a je možné beze změn v zapojení přepínat počet připojených LED.
Vstupní napětí by mělo být cca o 2V vyšší než potřebné. To si lehce spočítáte vynásobením asi 3,5V x počet LED (proud je samozřejmě konstantní).
Díky stabilizaci navíc světlo nebliká i při kolísání napětí z levného adaptéru (v GM se dají koupit už od 70,-)
Jen pro úplnost dodám, že uvedený LM317 má maximální proud 1,5A a 37V na výstupu (to dává přibližně 10x výkonových LED)
Sice nic novýho to není, ale snad to někomu pomůže. Já si takto udělal intim-světlo k PC, které jede skoro zadarmo a přepínačem si vybírám bílou/zelenou podle atmosféry ;)
-
Re: Zapojení svítivých LED
Tady jsou různá zapojení pro napájení i obyčejných i výkonových diod z různých zdrojů napětí.
http://amarokcz.wz.cz/N.htm
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal
Kall
ještě jeden dotaz stran zapojení LED:
je nutné při zapojení LED LUXEON na 12 V dodržet výkon 1,2W nebo stačí dodržet 350 mA?
Přesně tohle mě také zajímá,ale předchozímu tazateli se na tuto otázku nedostalo odpovědi.Pouze že 350mA je max. Taktedy znovu ale jinak:je možné napájet LED LUXEON z 12V zdroje s regulací na 300mA?Mám dvě diody a přemýšlím jak je napájet v autě.Klidně i v sérii,tak mi prosím poraďte.Díky moc předem. :rolleyes:
-
Re: Zapojení svítivých LED
Luxeony co se ještě pořád prodávají třeba v GESu jsou již dnes totálně zastaralá záležitost. LEDky se v posledních letech rychle zlepšují a v současnosti jsou nejlepší Cree LED, mají účinnost 3-5 vyšší než starý luxeon. Takže při stejné spotřebě svítí 3-5x víc...
K tomu napájení. Bílá LED má při napájení proudem 350mA napětí někde kolem 3V. Takže dvě v sérii budou mít 6V. Rychlé řešení je použít vhodný rezistor (cca 17 ohmu), ale to by bylo hodně neefektivní. To samé co by ti spotřebovaly ledky by se ti na rezistoru protopilo na teplo... Ideální tedy je použít měnič s konstantním proudem na výstupu. Třeba tenhle.
-
Re: Zapojení svítivých LED
Kazda ledka ma danej maximalni proud a to je jediny, co je podstatny, samo bezne se pouziva tak 1/2. Napeti zdroje je nezajimava informace, pokud nepreleze prurazny napeti (vetsinou nekolik kV). Ledku lze klidne primo pripojit do zasuvky, staci k ni dat kondenzator (samo spravne dimenzovanej).
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal
Jezevec
Ledku lze klidne primo pripojit do zasuvky, staci k ni dat kondenzator (samo spravne dimenzovanej).
Ne tak docela. Rek bych, ze tu ten problém uz nekdo nastínil, ted to ale nemúzu znova najít.
Náhodou jsem tu na tohle narazil, i kdyz jsou to uz léta, prece jen to tu sedí jako "dúlezité". Já sám jsem s touhle jednoduchostí sít - kond - dioda uz 2x narazil. Jednou jsem chtel kontrolku na termostatem spínanou plotýnku u sporáku a po druhé slo o usmernovací diody normálne koupené nabíjecky v lampe na kolo, co se strkala rovnou do zásuvky a kde bylo sítové napetí také srázené jen sériovým kondem - zhruba pri 5. zasunutí do zdi to ty diody odprazilo.
Jde o to, ze ten kond je pri pripojení v neurcitém stavu nabití. Takze v nejnepríznivejsí situaci je v prvním momente na té diode az 700 V na tvrdo - spicka 230V eff. = 325 V + tolerance napetí síte, to celé x2, kdyz byl kond nabitý práve na tuhle hodnotu v opacnémm smeru. Az 10 ms púlperiody 50 Hz, nez se to celé vystríbrí, dostatecne dlouho na odtavení i robustní usmernovací (malovýkonné) diody, natoz jemnocitné LEDky.
Takze z toho dúvodu to potrebuje jeste sériový odpor, který zarucí, ze ani pri tomhle napetí proud neprekrocí maximální prípustnou krátkodobou spickovou hodnotu. Samozrejme, ze ten pak za provozu topí a zhorsuje úcinnost toho celého, ale to je bohuzel zivot, alternativa by byla jedine slozitejsí elektronika.
Potom, jak známo, kondenzátorem tece jenom strídavý proud, zatímco LEDkou jen stejnosmerný. Takze 2 moznosti:
1. Napetí pro LEDku usmernit 2-cestne mústkem - pri dimenzování sériového odporu je treba vzít v potaz i tyhle diody. Ty sice zpravidla vydrzí mnohem víc nez taková útlocitná LED-ka, nicméne prekontrolování podle katalogových hodnot doporucuju. Nemám to tak presne v hlave, abych za to dal ruku do ohne, jde i o to, jakými diodami se usmernuje, jestli se treba nevynucuje z prostorových dúvodú jejich titernost.
2. 2 LEDky antiparalelne: Tady je ovsem urcité riziko, ze jimi nebude protékat úplne presne stejný proud, kondenzátor se bude pomalu nabíjet jedním smerem a obzvlást pri trvalém provozu by tím mohlo svetlo pomalu slábnout az by zhaslo docela a rozsvítilo se zas teprv az po vybití kondu.
A k otázce pretízení proudem nebo výkonem:
Jediné, co takhle diodu znicí, je teplo, tedy watty. Protoze se ale u diody pracuje predevsím s proudem a ten vetsinou s dostatecnou presností definuje i ty watty, tak se jako orientacní hodnota pouzívá proud. Uz jen proto, ze to cele je dost nepresné i díky tomu, ze podmínky chalzení lze jen málokdy úplne precizne definovat. Proto je vzdycky dobré nechat urcitou rezervu, pokud lze. Kdyz to ale nekdo chce opravdu presne, musí vycházet VA-charakteristiky (volty na diode, ne na zdroji, samozrejme), z wattú a jeste k tomu pribrat i zpúsob odvodu tepla. Kdyz se chce, múze to být i dost slozitá veda;). Co je s konecnou platností rozhodující, je teplota prechodu. Na tu prímo se clovek ale za normálních okolností nedostane.
-
Re: Zapojení svítivých LED
Ahoj ve spolek. Potrebuju poradit jak zapojit červenou diodu a bílou na jeden zdroj
-
Re: Zapojení svítivých LED
Priznám se bez mucení, ze z tohodle pozadavku prílis moudrý nejsem. Múzes trochu blíz opsat, co z toho má nakonec vylézt?
-
Re: Zapojení svítivých LED
pokail maju rovnaku VA charakteristiku tak kludne aj spolu do serie + odpor . Na 100% vsak bude kazda ina takze kazdej vlastny odpor .
-
Re: Zapojení svítivých LED
Citace:
Původně odeslal
proe
pokail maju rovnaku VA charakteristiku tak kludne aj spolu do serie + odpor . Na 100% vsak bude kazda ina takze kazdej vlastny odpor .
Pri seriovym zapojeni prece na zadny VA charce nezalezi, jen celkovy proud nesmi prekrocit mezni proud te slabsi diody. Ubytek na odporu by byl rozumny tak aspon 2V, takze to bude vyzadovat celkem cca 7V napajeni a vice. Pokud ma kazda dioda jiny proud nebo je potreba napajet z 5V, tak pro kazdou diodu odpor zvlast.
-
Re: Zapojení svítivých LED
to s tym prudom v serii je pravda ako pises , len pri rozdielnych VA char. kazda mu bude svietit inou intenzitou...predpokladam ze chce aby obe svietili pekne :)
-
Re: Zapojení svítivých LED
Spis nez o VAchar de o svitivost a jeji subjektivni vnimani, treba modrejm LED typicky staci par mA a uz to sviti jako prase - nastavuju proud klidne 1mA i min. Naopak cervena zas vetsinou tolik nezari, takze tam tech std. 20mA.
-
Re: Zapojení svítivých LED
Jj nesou jiné energie, takže subjektivně strašnej rozdíl. Ale eksperti tě budou přesvědčovat, že 21W žárovka v zadní červené mlhovce je strašný zlo, zatímco když máš slabý světla a vyjede proti tobě něco se 4× 55 W bílý (až do modra), případně xenony, laser vepředu, tak je to úplně kůl.
Jinak k diodám, teďko jak se rozmáhaj ty LEDkový věci, to je mor. Kvůli té dynamické chrakteristice mají jenom velmi úzkej bod dobré efektivity. Když se to nechá volně jako rezistor, tak sice hodně svítí, ale pečou jak kamna. Když se proud omezí moc, tak svítí málo. Samozřejmě číňan všude strká zdroje 30-50 V, 80-100 V a taková rány a tam desítky diod v sérii, jak to dopadá asi netřeba říkat. Nebo no-name čína náhrada žárovek v autě - všechno na 12 V, takže při 14 to peče jak prase, diody odchází jedna za druhou. Aspoň že Cree se v tomhle drží a ty jejich jsou krásně vlažňoučký, ale maj omezenej výběr něčeho, co nesvítí hlavně dopředu přes čočku…
Dokonce údajně třeba do E27 už tam ani nedávaj zdroj, co zdroj, ani kondenzátor. Mi řikal známej, koukal do jednoho takovýho zázraku, normálně rezistor a sto diod v sérii. Ty vole!
-
Re: Zapojení svítivých LED
Ovsem co tam pece nejvíc, je napojení pívodú, pres které tece, kdyz je to dejme tomu nejaká 5 W, pres 1, snad i skoro 2 A (kolik V má vlastne takováhle ledka? pocítám tak neco okolo 3 ..?) na malé plose. Kdyby to bylo víc diod uz z výrobního procesu odladených jako stejné v sérii, potece pri stejném svetle mensí proud mude to podle toho mín topit a na tech sítových 110 - 240 V je jeste bohatá rezerva na cistý zdroj nejakých dejme tomu 30 V.
Jinak co je taky mor, tady to ted dávaj do nízkých poulicních lamp a i to oslnuje jak kráva. Nic proti energeticky efektivním zdrojúm svetla - i kdyz ledky vidim jako správný smer, jeste to má detské nemoci a podle me zbytecne.
Onehdá jsem jel vecer za jednim cyklistou, a ten mel krome uz tak silnýho ledkovýho zadního svetla jeste ostrý, asi taky ledkový bleskový cervený blikadlo, aby ho náhodou jó nekdo neprehlíd; myslel jsem, ze z toho oslepnu. Nastestí jsem jel o dost rychlejc, takze jsem ho brzy predjel. Ale rikám si, lidi co maj takovýhodle strachu, ze se musej takhle zvýraznovat, at radsi zústanou sedet doma na zadku nebo jezdej (M)HD, a na tom kole nikam nelezou. A jestli to maj, aby tim svetu predvádeli svoje ego, tak tim spís.
-
Re: Zapojení svítivých LED
Tyhle monstrozity se používaj zřídka, maximálně tak v reflektorech, běžně do 1 W, na těch skládanejch spíš tak do 0,5 W, tam jsou proudy zanedbatelný.
Obecně je lepší svítit víc a být vidět. Pokud tam sto let nic nejelo, máš už relativně slabý světla a najednou von, tak tě to voslnilo hlavně proto, že sis před tím přivyknul na malej světelnej tok. Jezdit proud aut nebo za šera, tak to bude akorát.
-
Re: Zapojení svítivých LED
Ona nekde je hranice, kde víc uz v podstate víc neznamená. Já jezdim porád s klasickym zárovkovym osvetlenim a postrannim dynamem a za s tech svých 50 let na kole, jinakzto asi 300'000 km jsem uz mel neco kolizí i bouracek s autama a nikdy to nebylo za tmy. Vzdycky za jasného dne, dobrýho pocasí, ze me ridic/-ka na vzdálenost ca. +/- 5 m "prehlíd/-la". Takze o osvetlení kola to není, kazdopádne prinejmensím mnohem mín, nez si lidi myslej. Daleko spís bych rek, ze za tmy lidi dávaj nistinktivne na vsechno mnohem víc pozor, zatimco ve dne se jim zdá vsechno v pohode, to se nic nemúze stát, cumej kde co lítá a ne tam, kam maj.
-
Re: Zapojení svítivých LED
Jo ty LEDkovy verejny osvetleni sou ted v mode, v jedny vesnici pres kerou jezdime na chatu to taky namontovali a to svitidlo ma tvar takove placky bez jakehokoliv reflektoru, ktery by omezoval bocni svit, takze pri pohledu na lampu oslnuje vic a subjektivne mi pride, ze je osvetlena poradne jen oblast pod lampou a uprostred mezi lampama je vetsi tma. Podle nake normy by tenhle pomer intenzit max/min nemel byt vetsi nez neco...
BTW z hlediska setreni ty ledky pro domacnosti stejne mozna pozbudou vyznam, projdou-li novy tarify uctovani elektriny, to se zas chysta na lidi velezlodejina, doufam ze to pres Vitaskovou neprojde.
-
Re: Zapojení svítivých LED
Ta k tomu možná nebude mít už možnost co říct, když ji zavřou za něco, co objektivně nemohla spáchat :D
-
Re: Zapojení svítivých LED
No tak to nakonec dopadlo (zatim) dobre, cely NTS smetli ze stolu a musi to prepracovat. Takze dalsi mozny pokus o zlodejinu maji pry az v 2019...
http://www.ceskatelevize.cz/porady/1...6411000100303/ od 31:45
A doufam, ze Vitaskovy vyjde to odvolani a ze za ty solary pude sedet ten predchozi cinitel, ktery to schvalil a o kterem se nemluvi...
-
Re: Zapojení svítivých LED
Jo, Bohuš se eště musel vyjádřit jak to je fakt špatný, jen zapomněl, že to celý spískal, a už to teda můžou odložit. Ale co už. Dík, dal bych K+, já na tydle srágory už radši ani nekoukám, ale prej to eště nejde.
Ale začínaj ty zprávy dobře, hned jak budou zas obírat těžaře uhlí. Nestačí jim, že s ohledem na cenu energií (snad by měl konečně jít dolů i plyn, když šla cena na trzích tak na polovinu za posledních pár let) končí černouhelný doly v MSK, teď budou likvidovat i hnědouhelný doly. Checht, to zas budou brečet, až jim řeknou, že končí a propouští tisíce :D Hlavně až se zavřou další hnědouhelný elektrárny.
Hehe, o plynu tam taky mluví, takže VO cena šla na polovinu a ono se má zlevnit o 7-10 %! No to mi poser záda. Fakt si vozit z ukrajiny v cisterně na vlastní pěst topnej olej a benzín a srát tady na všechno.
-
1 Příloh-a(y)
Re: Zapojení svítivých LED
Citace:
Původně odeslal
RayeR
Jo ty LEDkovy verejny osvetleni sou ted v mode, v jedny vesnici pres kerou jezdime na chatu to taky namontovali a to svitidlo ma tvar takove placky bez jakehokoliv reflektoru, ktery by omezoval bocni svit, takze pri pohledu na lampu oslnuje vic a subjektivne mi pride, ze je osvetlena poradne jen oblast pod lampou a uprostred mezi lampama je vetsi tma. Podle nake normy by tenhle pomer intenzit max/min nemel byt vetsi nez neco...
Bude to asi neco takovýhodle, ne?
Já abych pravdu rek, nevim, jak ty zdejsí z blízka vypadaj. Vzdycky pod tim profrcim a jednak radsi koukám na cestu, druhak se mi nechce si pálit oci, abych do toho brejlil. A za svetla si na to nevzpomenu.
Tohle tady bylo v jednom odbornym casáku pred 3 rokama, ze tim chtej nekde v Mexiku osvetlovat nejakou 8-proudovou ulici.
-
Re: Zapojení svítivých LED
Jo, tvar zhruba odpovida, taky sem to chtel nekdy cestou vyfotit a prohlidnout si detail...
-
Re: Zapojení svítivých LED
Tak zas to konečně nedělá tendlencten světelej smog, ne? :D
-
Re: Zapojení svítivých LED
Nedelá to svetelnej smog jako treba bílý koule na sloupu nebo - co se taky v posledních letch casteji vídá - lampy zapustené do dlazby, co svítí nahoru. Nejpodstatnejsí cást svetelného smogu z poulicního osvetlení je dnes ale to, co se odrází od zeme a prilehlých objektú, popr. rozptyluje v mlze a prachu; v tom jsou tedy ty ledky naprosto stejné jako ostatní typy jen dolú svítících a nahoru odstínených lamp.
-
Re: Zapojení svítivých LED
Nedávno jsem zas jednou - v poslednim císle toho casáku, odkud je ta LED-lampa nahore - cet, jak se redukuje svetelný smog: V oblastech s malým provozem ty lampy normálne svítí jen na asi 10% výkonu a jen kdyz se neco blízí (auto, cyklista, chodec), tak se pozvolna rozsvítí na plno a kdyz je to pryc, tak se zas setmí. LEDky jsou na to ideální, i kdyz s novejsími modely sodíkových výbojek to prý jde taky; ty ovsem potrebují o tolik víc energie, ze se jejich nová instalace vetsinou nevyplatí. Majitelé prilehlých domú si prý ale casto stezují, ze trvalé plné osvetlení v noci zajistuje lepsí bezpecnost. I tohle je po téhle stránce ovsem lepsí, nez co se nekde na venkove delá, ze se po púlnoci verejné osvetlení proste zhasne.