Plus zvys Vcore NB, mne zvysenie na 1.425V pomohlo.
Printable View
Plus zvys Vcore NB, mne zvysenie na 1.425V pomohlo.
RAM mam tyhle http://www.czechcomputer.cz/product.jsp?artno=38525 a CPU chladim Noctuou.
To přidání V MB zkusím to jsem nedělal a RAM bych taky mohl dát 2,2V nísto základních 2,1V
3360 MHz /7 = 480 FSB to je uz docela hodne.
Velmi pravdepodobne to nedavaji tve pameti. 480x2 = 960. Chybu pameti Prime nemusi odhalit.
Muzes zacit tim, ze snizis nasobic na 6x ... to znamena 480x6 = 2880 to by mel tvuj C2D davat bez problemu s temi napetimi co zminujes.
Pak testuj MeTest86+. Pokud ti projdou alepson 3x pass bez problemu tak teprve zacni hledat chybu jinde.
Pokud to neprojde tak si na P5B Deluxe zkus pohrat s parametry pameti, dej tam treba 6x6x6x18 a ty dalsi subparametry dej alespon na 15, zvys napeti na pamtech na 2.3 a napeti na NB na 1.55.
Pokud to projde, tak stahni Orthos (misto Prime) a zacni treba na 440 FSB s nasobicem 7 a napetim klidne 1.45V a postupne zvedej frekvenci. Mezi zvedani udelej alespon 2 hodinovy test Orthosem. Az to pak neprojde tak sniz o 10MHz a otestuj Orthosem pre noc.
Teplota 70oC, to je z ceho (TAT, jina utilita)? Je to uz celkem vysoko, na dlohodoby provoz bych se poohlednul po lepsim chladici, nebo se spokojil s mensi frekvenci na nizsim napeti.
Jak rika muj kolega: Nevyplati se kupovat nic s 6-7X multiplikatorem ... :-)
Taky jsem na jeho ray nedal .. :-)
Díky za rady...vše to nějak vyzkouším...pravdou je že s voláží desky jsem si nehrál.
Co se týče FSB tak by to deska měla zvládat. Jinak v threadu o P5B deluxe jsem se dočetl, že pro testování RAM není uplně pokaždý ideální dát co nejhorší časování...nějaký RAM s tím můžou mít prej problémy.
Jinak Orthos ted používám na testy taky je to pohodlnější než zapínat 2×Prime - citlivost je prý velmi podobná.
Co se týče teploty tak jsem psal uplně tu maximální při Burnu (na testy), takže při provozu to taky bude někde jinde. No a koupit lepší chladič? To si mě docela rozesmál...zkoušel jsem Ninju...ted mam Noctuu, tak už fakt nevim co tam mam dát :-) (vodníka se bojim a efektivita vzhledem k ceně mi nepřijde jako lepší) to nemluvím třeba o nepraktičnosti u přenášení.
No, nejlepsi na testovani je asi 1x prime + HL2 .... :-)
Half-life 2 je totiz VELMI citliva zalezitost ... a s prime95 umi zazraky.
Co se tyce FSB tak nikdo ti nezaruci, ze zrovna tvuj kus zvladne tech 480 MHz.
Co se teplot tyka, tak mas mozna spatne uchyceny chladic, nebo nejaky problem s vetranim skrine.
Ja se s levnym Hyper TX chladicem nedostanu pres 65 stupnu v TATu ani pri VCore pres 1.5V a frekvencich 3.2 GHz, pri maximalni zatezi. (dlouhodbe pri zatezi Orthosem a napeti 1.4V a 3.1 GHz jsem max na 53 stupnich, to vse pri 25 stupnich ambientu).
Nekam k 70 stupnum jsem se dostaval s stockem kdyz jsem sel pokusne pres 1.5 V.
No, že bych to měl špatně uchycený se dá skoro vyloučit, protože s předchozí Ninjou jsem měl teploty ještě tak o 3-4st. výš. Noctuu jsem navíc nasazoval 2× a je tam pasta Zalman. Co jsem četl jinde tak tyhle teploty nejsou nijak nenormální...navíc je potřeba si uvědomi že 3,4GHz už zase topí trochu jinak než to tvoje...
Aku verziu TAT pouzivate?
Je to pri 2x 100% load v TAT. Vsechny setrici a throtlici technologie povypinany.
Ted jsem to rano znovu testoval:
Obe lehce kolisaji kolem:
52 stupnu pri 3100 MHz a 1.40 V, ambient je zrovna 22 stupnu.
59 stupnu pri 3200 MHz a 1.49 V, amb 22 st.
Napeti uz jsou s Vdroop 0.025V, takze v BIOSu je vic.
Verze TAT 2.05.2006.0427
Pokud pustim Orthos a TAT jen monitoruje tak jsou teploty cca o 4-5 stupnu nizsi. (tedy kolem 54 pri 3200 a 1.49)
C2D 6420 nic moc kousek. P5B Deluxe. Chladic CM Hyper TX za 500,-.
Skrin CM 532 s 12 cm pomalobeznym fanem navic.
CPU vetrak na HyperTX ukazuje 1896 RPM.
Zatez pri kazdem testu kolem 5-10 minut.
Co se ti nezda? Se stockem jsem byl pri stejnym nastaveni nejmin o 15 stupnu vejs pokud si dobre pamatuju.
Mne tie teploty pridu dost nizke o pravde. Mozno to bude ale tym, ze mas proste iny kus CPU. Vplyv dosky by sa tu snad pri merani TAT prejavovat nemal.
Ja TT Big Typhoon na 1300 rpm pri 3GHz a 1.31 real voltazi mam pri TAT Loade 70-75 C, zavislosti od teploty v izbe (teplomer zial nemam). Mam samozrejme jadro allendale. Na druhu stranu chladenie celkovo nemam nijak podpriemerne, je to dobre vetrane ... tak neviem ...
Teploty ktere pise SASA jsou nizke, bud spatny SW nebo senzor CPU... Testoval jsem vice CPU, na ruznych MB, ruzne pasty atd a vzdy s stock chladicem tepltoty lezly k 80°C, s Noctuou nebo Scythe Mine 70-78°C.
Aby mel 52°C ... ;D pobavil jsem se.
Ano přesně tak :-) V klidu mam tak 55st. a jen v uplný zatížení je těch 70st
Třeba s BOXem je těch 55st taky...ale na deafult :-)
TAT pres 70 stupnu neni rozhodne duvod ke klidu a uz vubec to neni normalni.
http://forumz.tomshardware.com/hardw...ict221745.html
Mě právě Ninja taky moc nepřesvědčila...tak jsem tam dal Noctuu a myslel jsem že to pujde tak o 8st dolu...a taky to neni žádná slává...nevim co dělám blbě....třeba ten muj kousek topí víc...asi sem hodim foto case a chlazení.
Ja mam v TAT (100% TAT zatez na obe jadra) taky pres 70°C kdyz jedu na 2.8GHz (1.375V) .. Ninja na cpu, case je imho slusne chlazena.
Mam tiez Freezera 7 Pro a s 2160 @ 9*333 pri 1.336/1.312V (idle/load) mam v TAT 75 stupnov. Vetrany case...
Zkuste tedy postnout verzi TATu.
Podle tohohle threadu: http://www.hardforum.com/showthread....1174781&page=2
Jadra Allendale udavaji zrejme o 15 stupnu vyssi teplotu TJunction nez original Conroe.
Resp roli asi hraje TCaseMax 85 nebo 100. u jednotlivych kousku.
Takze tam kde je u me normalnich 55 stupnu tak u Allendale to odpovida 70 == vsichni spokojeni.