Printable View
NAzdarek, mam problem v Slackwary 8.2 nainstalovat sietovku eth1, ktory ma sluzit na obsluhu lokalnej vnutornj siete z ktorej sa bude routovat na Inet. Internetova karta eth0 mi ide.
Poradte, pretoze proc-pci ju nenajde, ani ifconfig. skusal som aj netcongig a pkgtool nic moc. Iba apropos ju nasiel ako 3com 3c 589. poradte ako ju rozchodit.
Kamosovy ju naslo hnet samo, mne nie.Vdaka.
3c589 ??? To je predsa PCMCIA karta...
nie, ta moja je v jedinom ISA slote co mam. Standardna
3com TP/BNC karta.Ked tam hodim knopixa, najde ju okamzite.
Neviem v com je problem. nikdy nerobi problemy, este aj RED HAT ju najde, ale ten teraz nechcem nahadzovat, skusam tento.
A nie je to nahodou 3c509 ??? modprobe 3c509
OKi, sietovku som rozchodil podla root.cz. takze ta ide, akorat mi dajako nejde nic z kompu. ani do lokalky, ani na net, mam dajako opacne nastavene ovladace ci co. pinam sam seba, ale vom na ove strany nic nejde.
napis sem vypis prikazu route
To skusam samozrejme kaydu chvilu, abz som neprisiel o realtec a internet.
Tak som trochu mudrejsi, ovladacmy to nebude. V ethtool je default nastavene eth1 status offline a nejde mi prepnut online, sice viem ako ale Operation is not supported. Potom som vymenil 3com a nejde ani ta, takze kartov to nieje.
pingat sa mi stale neda. nmap tvrdi, ze nieje zapnuta.lsmod-om som sprevadzkoval moduly.
Tcpdump pise same kraviny, take nezaujmave.
Pokial to nebude v tom, vo Win mam IRQ7, v lin 3[12]
Dost by bodlo, keby ste mi na mail poslali 3c509[b].c modul, nech to poriadne preverim
Route pise vsetko v poho, aj rootovanie je ok[ z virtualnej 18 na 70 to ide] ale karta poriadne nejde.
v RC.D skriptoch toho moc nic nieje, neviem to nakonfigurovat.
Idem sa trapit dalej, cafte
muze mit kolizi irq, taky muze byt prepla na aui nebo koax, to si pak po tp nepingnes. ale tyhle isa jsou vetsiunou hlavne o tech kolizich irq. tak si pohraj. nastavuje se to pres utility od 3comu z dosu
3 mangatono
dmesg Ti nepise zadnou chybu IRQ preruseni ?
Me to jednou u sitovky psalo a bylo to chybnym nastavenim BIOSu.[/b]
a co hovori mii-tool ?
:idea: Takz podla mna niesu konflikty irq, ale pre istotu dmesg (dam to sem cele, pjominte )
:idea: A este ten ethtoolKód:Linux version 2.4.22 (root@midas) (gcc version 3.2.3) #6 Tue Sep 2
zone(1): 36848 pages.
zone(2): 0 pages.
Kernel command line: BOOT_IMAGE=Linux ro root=307
Initializing CPU#0
Detected 791.415 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1579.41 BogoMIPS
Memory: 158800k/163776k available (1813k kernel code, 4588k reserved, 614k data, 116k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
CPU: After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU: Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Coppermine) stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb350, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
vesafb: framebuffer at 0xd0000000, mapped to 0xca80d000, size 937k
vesafb: mode is 800x600x8, linelength=800, pages=7
vesafb: protected mode interface info at c000:0f03
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 512 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 7777K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:07.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt2c686a (rev 22) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:DMA
hda: WDC WD200EB-32CSF0, ATA DISK drive
blk:queue c03a9d80, I/O limit 4095Mb (mask 0xffffffff)
hdd: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=2434/255/63, UDMA(33)
hdd: attached ide-cdrom driver.
hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 >
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
8regs : 1309.200 MB/sec
32regs : 785.200 MB/sec
pIII_sse : 1621.600 MB/sec
pII_mmx : 1774.800 MB/sec
p5_mmx : 1852.000 MB/sec
raid5: using function: pIII_sse (1621.600 MB/sec)
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
LVM version 1.0.5+(22/07/2002)
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with orderd data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 116k freed
Adding Swap: 297160k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 122M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 64M @ 0xd8000000
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 00:09.0
PCI: Sharing IRQ 11 with 00:07.2
PCI: Sharing IRQ 11 with 00:07.3
eth0: RealTek RTL8139 Fast Ethernet at 0xca94f000, 00:06:4f:0a:2e:9b, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
isapnp: Scanning for PnP cards...
isapnp: Card '3Com 3C509B EtherLink III'
isapnp: 1 Plug & Play card detected total
eth1: 3c5x9 at 0x220, 10baseT port, address 00 20 af 6b fd a7, IRQ 12.
3c509.c:1.19 16Oct2002 becker@scyld.com
http://www.scyld.com/network/3c509.html
PCI: Found IRQ 5 for device 00:07.5
PCI: Setting latency timer of device 00:07.5 to 64
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Found IRQ 11 for device 00:07.2
PCI: Sharing IRQ 11 with 00:07.3
PCI: Sharing IRQ 11 with 00:09.0
uhci.c: USB UHCI at I/O 0xd400, IRQ 11
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:07.3
PCI: Sharing IRQ 11 with 00:07.2
PCI: Sharing IRQ 11 with 00:09.0
uhci.c: USB UHCI at I/O 0xd800, IRQ 11
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
parport0: PC-style at 0x378 [PCSPP,EPP]
parport_pc: Via 686A parallel port: io=0x378
Kód:Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised auto-negotiation: Yes
Speed: 100Mb/s
Duplex: Full
Port: MII
PHYAD: 32
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: pumbg Wake-on: d
Current message level: 0xffffffff (-1)
Link detected: yes
Settings for eth1:
mii-tool hlasi eth0 okiKód:Supported ports: [ TP AUI BNC ]
Supported link modes: 10baseT/Half 10baseT/Full
Supports auto-negotiation: No
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 10Mb/s
Duplex: Full
Port: BNC
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000002 (2)
Link detected: yes
eth1 (3com)siocgmiiphy no eth1 failed. operation not supported, a na tom momentalne pracujem.
Inak na 2 PC sa nepingnem, ale cez arp ho vidim ako incomplete. Dik za pomoc
[edit by Rainbow] Dal som to do citatelneho tvaru
Hovoril som, ze to bude 3C509 ;D
Aku mas dosku ??? Nemas nahodou PS/2 mys (na IRQ12) a zvukovku (na porte 220h)?
IMHO treba nabootovat do DOSu a programom 3c5x9cfg (od 3Comu) nastavit tu kartu tak, aby bolo vypnute Plug&Play, nejaky volny port (napr. 300h), IRQ (napr. 10) a pouzity port (TP/BNC/AUI).
mii-tool na tej karte nefunguje, lebo ta karta nema MII.
Ja sa len tak blbo spytam, tvoja siet je coax kabel ??? lebo ked nie tak mozes pingat kolko chces...
Samoyrejme ye je Coax, inak bz som to tak neprepol, ono to bolo default TP. Y toho som chvilu magoril, ale potom sa podarilo prepnut, ale furt ma sere ten PHYAD=0, NECHAPEM
Teray som to posahal a uy mi ani modul nenahachuje. sakra. nemozete mi pomoct cez SSH? Spravim uzivatela a tak. pokecame.
Cez telnet by bolo tiez dobre, ale ten mi ide len v noci, ani to nechapem, ale to bude asi v serveri.
Ale vobec nechapem to, ze ho najde, ale ze Incomplete. Potom to sem hodim.
nepojde a s ne2k ide Tp cast ale BNC ani neprdne. Aku mam pouzit, lebo nikde sa mi neda stiahnut poriadny Modul
Tak este raz a cele, dajako sa to posralo. Mam realtec pci 8029.nemam modul na spustenie. s 8139too to nejde a s ne2k ide Tp ale BNC nie. nemam kde stiahnut modul aj google som skusal ale s malym uspechom. Nechce my vypisat detaily Ethtool eth1 aby som mohol zmenit na bnc. co robyt???
Na 8029 je modul ne2k-pci, ktery jsem jeste nevidel, ze by nechodil. Medium se musi vybrat pres diagnosticky SW, ktery je na diskete ke karte. Pak to chodi skvele, az na zatez CPU :oCitace:
Původně odeslal mangatono