3C905C - nejde full duplex

V robote na serveri je tato sietovka. Nech sa snazim ako chcem, na switchi stale svieti 100mbps half duplex. "mii-tool -F xxx" ani "mii-tool -A xxx" nerobi nic. Co s tym kua je ??? Jadro Linux 2.6.7.

Kód:

root@server:~# lspci | grep 3Com 02:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)

Kód:

root@server:~# mii-tool -v eth0: link ok product info: vendor 00:10:18, model 23 rev 6 basic mode: autonegotiation enabled basic status: link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control

Kód:

root@server:~# ./vortex-diag -aa vortex-diag.c:v2.16 1/12/2004 Donald Becker (becker@scyld.com) http://www.scyld.com/diag/index.html Index #1: Found a 3c920 Series NIC adapter at 0xa800. Station address 00:04:76:14:a9:17. Receive mode is 0x07: Normal unicast and all multicast. The Vortex chip may be active, so FIFO registers will not be read. To see all register values use the '-f' flag. Initial window 4, registers values by window: Window 0: 0000 0000 0000 0000 0000 00bf ffff 0000. Window 1: FIFO FIFO 0700 0000 0000 007f 0000 2000. Window 2: 0400 1476 17a9 0000 0000 0000 0052 4000. Window 3: 0000 0240 05ea 0020 000a 0800 0800 6000. Window 4: 0000 0000 0000 0cfa 0001 8880 0100 8000. Window 5: 1ffc 0000 0000 0600 0807 06ce 06c6 a000. Window 6: 0000 0000 0000 3401 0100 6918 6602 c000. Window 7: 0000 0000 0000 0000 0000 0000 0000 e000. Vortex chip registers at 0xa800 0xA810: **FIFO** 00000000 0000001c *STATUS* 0xA820: 00000020 00000000 00080000 00000004 0xA830: 00000000 5ccfa331 013cd120 00080004 0xA840: 00cb555b 00000000 000000b7 00000000 0xA850: 00000000 00000000 00000000 00000000 0xA860: 00000000 00000000 00000000 00000000 0xA870: 00009000 00000000 01600160 00000000 DMA control register is 00000020. Tx list starts at 00000000. Tx FIFO thresholds: min. burst 256 bytes, priority with 128 bytes to empty. Rx FIFO thresholds: min. burst 256 bytes, priority with 128 bytes to full. Poll period Tx 00 ns., Rx 0 ns. Maximum burst recorded Tx 352, Rx 352. Indication enable is 06c6, interrupt enable is 06ce. No interrupt sources are pending. Transceiver/media interfaces available: 100baseTx 10baseT. Transceiver type in use: 100baseTX. MAC settings: full-duplex. Station address set to 00:04:76:14:a9:17. Configuration options 0052.

Kód:

root@server:~# ./vortex-diag -ee vortex-diag.c:v2.16 1/12/2004 Donald Becker (becker@scyld.com) http://www.scyld.com/diag/index.html Index #1: Found a 3c920 Series NIC adapter at 0xa800. Station address 00:04:76:14:a9:17. Receive mode is 0x07: Normal unicast and all multicast. EEPROM format 64x16, configuration table at offset 0: 00: 0004 7614 a917 9200 0225 0048 574d 6d50 0x08: 2940 0800 0004 7614 a917 8020 0000 00aa 0x10: 72a2 0000 0000 0240 0000 0005 0000 10b7 0x18: 1000 000a 0000 6300 ffb7 b7b7 0000 0000 0x20: 00b0 1234 5600 0000 0000 0000 0000 0000 0x28: 0000 0000 0000 0000 0000 0000 0000 0000 0x30: ffff ffff ffff ffff ffff ffff ffff ffff ... The word-wide EEPROM checksum is 0x6264. Saved EEPROM settings of a 3Com Vortex/Boomerang: 3Com Node Address 00:04:76:14:A9:17 (used as a unique ID only). OEM Station address 00:04:76:14:A9:17 (used as the ethernet address). Device ID 9200, Manufacturer ID 6d50. Manufacture date (MM/DD/YYYY) 1/5/2001, division H, product MW. A BIOS ROM of size 0Kx8 is expected. Transceiver selection: 100baseTX. Options: force full duplex, link beat required. PCI bus requested settings -- minimum grant 10, maximum latency 10 (250ns units). PCI Subsystem IDs: Vendor 10b7 Device 1000. 100baseTx 10baseT. Vortex format checksum is incorrect (26 vs. 10b7). Cyclone format checksum is incorrect (0x9b vs. 0xb0). Hurricane format checksum is correct (0xb0 vs. 0xb0).

insmod

Me se osvedcilo prepinat pri nahrati modulu,
#modprobe 3c59x options=0x200 , ale nevim jestli pomuze, nedavno jsem mel v kompu sitovku, ktera mi s donaldovym driverem poradne nejela, a musel jsem pouzit tu od 3COMu.
Jedu tak 2.6kovy kernely

Teraz s tym nic robit nemozem, lebo cez SSH je to dost nebezpecne...a navyse nemozem pozerat na LEDky switchu. To bude zase "sranda" - driver som zakompiloval do jadra - myslel som si, ze to bude fungovat bez problemov... :roll: Ked vyjde jadro 2.6.8, tak to asi cele prerobim a pripadne vyskusam driver od 3Comu.

Tak driver od 3Comu nevyskusam, lebo je takmer 3 roky stary...pre 2.4.x :roll:

/usr/sbin/ethtool -s ${IFACE} port aui duplex full

takhle to mam pro ronju, ale jestli to fackt jede full duplex vi Buh. Ono se to pri half chova uplne stejne.

Pak mam jeste trochu jinsi mrsku
# eth1 - PCI 10/100 3c595 XL - LAN
alias eth1 3c59x
options eth1 options=4
# options eth1 options=4 full_duplex=1

ta zase pri full duplex sice jede, ale je tam chyb jak maku.

Kód:

root@server:~# ethtool eth0 Settings for eth0: No data available

To tam zjavne nefunguje. U mna doma to funguje:

Kód:

bash-2.05b# ethtool eth0 Settings for eth0: Supported ports: [ AUI BNC ] Supported link modes: Supports auto-negotiation: No Advertised link modes: Not reported Advertised auto-negotiation: No Speed: 10Mb/s Duplex: Half Port: BNC PHYAD: 0 Transceiver: internal Auto-negotiation: off Current message level: 0x00000002 (2) Link detected: yes

ale prezmenu nefunguje mii-tool ;D (3c509 zjavne nema MII)

zkus utilitku primo od 3comu, tam to jde nastavit na tvrdo

Zajtra tam idem, tak vyskusam ten DOSovsky program - najprv na PC vedla (je tam rovnaka sietovka, ale windows...) a potom na serveri. V tom Linuxovom driveri je asi nejaky bug, ked to vobec nereaguje na mii-tool...

Jo mam obdobny problem.... ethtool nefunguje a porad nahazuje 10Mb HD... pokud nastavym mii-tool 100Mb FD tak se nic nestane, jadro 2.6... Je taky 3Com ale jedna 590B a druha 590C... delaji to obe

Tak uz som to vyriesil. Tym DOSovskym programom (3c90xcfg) som zistil, ze to bolo nastavene na 100mbps full-duplex. Nastavil som vsetko na AUTO, ulozil, vypol a zapol - a potom to neslo vobec - ani LINK. Tak som vypol a zapol znovu a uz to ide na 100mbps full-duplex ;D Vyriesil sa tym problem s pomalostou siete medzi serverom a ostatnymi pocitacmi, ktore isli na 100mbps full-duplex.