Printable View
Neviete o nejakom softe ktory by podporoval tento chipset?
Na SiS-745 som pouzival k velkej spokojnosti S2kCtl.
Bohuzial sa mi nepodarilo rozbehat chladenie u SiS-741 ani cez S2KCtl, VCool, CPUCool, CpuIdle, nepoznate este nejaky SW resp. hodnoty pre WPCredit (ci ako sa vola ten soft) na zmenu priamo v BIOSe?
Zkus podle tohoto clanku nastavit WPCR Editem http://www.pctuning.cz/titulnistrana...=2&ArtId=17850
Pise se tam ze vsechny SiS 74x by mely mit podobny nastaveni, takze:
Rx6A[bity 4-0 enabled] = ACPI S3/S1/C3/C2/C1 Disconnect Enable
a kdyz to nepujde tak:
Rx6B [bit 0 – enable] = Halt disconnect
precital som si clanok, precital som si co si prave napisal, cumim na obrazovku WPCREDIT a absolutne nic mi to nehovori, ziadne Rx6A ci RX6B tam nikde nevidim, grr, som max. nasratyCitace:
Původně odeslal MV
EDIT: tak po ICQ konverzacii s MV sme dospeli k tomu, ze Rx je register, ze 6A sa nastavuje poziciou riadok 60, stlpec 0A, kde sa prepisu same nuly na: 00011111, nastavi sa Set, co nasledne sposobi okamzite vytuhnutie systemu
pak sme skusili register 6B, kde sme ho prestavili z 0000000 na 00000001, po Set to normalne zmodralo a nastavilo sa, ale nemalo ziadny vplyv na teplotu
SW CoolON by mal podporovat aj chipset SiS-741, ale rovnako ako u WPCREDIT po nastaveni registrov dojde k uplnemu vytuhnutiu PC, kedy sa na obrazovke zjavia akesi pasy a nepomoze ine nez tvrdy reset, nevie niekto ci to nemoze sposobovat nejake nastavenie BIOSu alebo proste nie je mozne vtlct SiS741 SW chladenie a autor CoolON to tam pridal len teoreticky...
Zkus nastavit ve WPCREDIT Rx6C-6D = 0001Citace:
Původně odeslal Markoff
SW chlazení SiS741 by mělo být stejné jako u SiS746.
CoolON by měl správně podporovat SiS741 až ve versi 1.23, nevím jestli jsi měl tuhle versi.
The north bridge of AMD (751/761) with, we have become the setting, bit18 of offset 60-63h of the host bridge Halt Disconnect Enable, when here is designated as 1, separating is possible. By the way, bit17 with Stop Grant Disconnect Enable, with CoolON makes both 1.
In case of KT133 type when bit7 of register 52h with Disconnect Enable When STPGNT Detected, designates here as 1, separating can do with the north bridge of VIA. With KT266 system 92h is used in place of 52h, it is necessary furthermore for Disconnect Enable When Halt Detected to be added by bit1 of 95h, to make both 1. With KT400 system, 92h/95h is modified to D2h/D5h. Furthermore, because can be moving KT880 to the register 82h/85h of function.
With the north bridge of SiS, 730 systems 6Bh, 735-745 6Ah, after of the 746 bit0 of 6Ch C1 (Halt) has become Disconnect. With SiS735 bit3 of 6Ah S1 (StopGrant) is information, Disconnect, but here seems that usually becomes effective.
It is detailed unclear, concerning the north bridge of nVidia, but as for nForce it seems that when in 11b, with nForce2 bit7-4 of 6Fh is designated as 0001b, separating can do bit3-2 of E7h.
-------------------------------------------------------------------------------------
Takže zde je uvedeno bit0 registr 6C umožní přechod do C1 tedy hlat stavu..., takže ten Rx6C Bit0 nastav na enable - 1
Ano funguje to, velka vdaka!
Takze pre SiS741 funguje register:
6C (pre lamy suradnice vo WPCREDIT 60-0C) a bit 0 na enabled (1)
Idem skusit napisat autorom chladiacich softov.