Scháním zapojení kabelu k UPS Chloride Power Start 600? Nemáte ji někdo, že by se oměřil kabel? Sériovej kabel se připojuje do RJ12 konektoru (telefonní kostka) na UPS.
Printable View
Scháním zapojení kabelu k UPS Chloride Power Start 600? Nemáte ji někdo, že by se oměřil kabel? Sériovej kabel se připojuje do RJ12 konektoru (telefonní kostka) na UPS.
To ji fakt nikdo nemá ?
P.S. Smiřuji se s tím, že asi ne ...
Skúsil si sa opýtať tu: http://www.chloridepower.com/content...hnicalquestion
BTW: kde inde by ti mohli poradiť lepšie ???
Zkoušel a zkoušel jsem i tady http://connectivity.chloridepower.com/ a poslali mi bohužel zjevně špatné zapojení, protože signálová zem je tam na jiném pinu, než skutečně je a pochopitelně nefunguje. Poukázal jsem na to a od té doby se neozvali ...
Ma to byt akoze RS-232? Ak ano, tak by to nemalo byt zlozite (hadam to ma RS-232 urovne a nie TTL). RJ-11 ma 4 piny, takze ak je jeden GND, mas uz len 3 - jeden z nich bude RXD, dalsi TXD a posledny mozno nic.
Bohužel to není tak jednoduché, je tam RJ12 a má obsazených všech 6 pinů, simple signaling jsem rozchodil a vyrobil funkční kabel, ale potřebuju smart (a UPS ho umí), protože chci mít možnost nastavit citlivist, pípání atd.
Takhle vypadají napětí, která jsem změřil:
normální provoz
1 4.5V
2 5V
3 0V
4 zem
5 0V
6 5V
UPS jede na baterky
1 4.5V
2 5V
3 5V
4 zem
5 0V
6 5V
Battery low
1 4.5V
2 0V
3 5V
4 zem
5 0V
6 5V
Zkoušel jsem snad všechny možný varianty zapojení a nic, buď je tam nějaká záludnost nebo je potřeba nějak sériovou komunikaci nastartovat, třeba jako u UPS Powerware.
Nemá k ní někdo náhodou aspoň starší komunikační software "VIGILANT 7" nabo DOSový "WDIALOG"?
Možná,že s tím novějším softem nechodí, byť by podle všeho měla ...
Popis UPS je tady: http://www.emc-world.dk/komponenter/...powerstart.pdf
Díky :-)
Tak jsem se radoval předčasně :-( , ty softy jsou bohužel nekomletní, wdialog má mít 3 755KB a vigilant 7 má mít 1 930KB, oba jsou menší nejdou rozbalit a ani po opravení nejsou použitelný.
Takže kdyby se někomu někde válely, byl bych za jejich poskytnutí vděčný.
P.S. A kdyby někdo měl DOSový APC Power Doktor, taky by se hodil.
Z kazdeho chyba na konci len 1 byte - staci tam pridad nulovy byte alebo to opravit programom pkzipfix... Toto je standardny problem suborov z archive.org.
vigidemo.exe ma 1182368b (+ jeden chybajuci byte), dialog.exe ma 971218b (+ chybajuci byte).
Zipfix zabral, ale je zajímavé, že Winrar to nezvládl ...
Teď už to jenom testnout :-)
Tak zase nic :-( Buď je špatný zapojení kabelu nebo rozhraní UPS, tipuju spíš kabel.
Kdyby měl někdo nějakej nápad, tak sem dávám obrázky UPS a zapojení toho kabelu, co mi poslali a nechodí:
http://images.ciao.com/iuk/images/pr...ct-5462772.jpghttp://web.telecom.cz/pewstec/pstart600.jpg
http://web.telecom.cz/pewstec/drawing.jpg
Za každej tip budu vděčnej.
Vyzera to tak, ze ty mas tie piny ocislovane opacne ako oni (u teba je GND na 4, u nich na 3). Este sa mi nezda to, ze sa to ma pripojit priamo na seriovy port a pritom tam su TTL urovne...
To mě taky napadlo, přitom podle toho jejich popisu číslování zem skutečně je na 4, rozebral jsem UPS a koukal kam jednotlivé piny vedou. To, že je 4 zem, jsem usoudil z toho, že na RJ12 konektoru v UPS jsou malé keramické odrušovací kondenzátory a všechny jsou zapojené na pin 4 a jednotlivé další piny. Všechny piny pak končí v řídícím procesoru UPS, na něm je napsáno Motorola Ondyne (Ondyne je skutečný výrobce UPS, je to i na plošňáku) a nějaká čísla, bude to asi zakázková výroba, takže z toho víc asi nevykoukám. Zkoušel jsem i různé varianty zapojení, podle schématu, s obráceným číslováním, pak různé kombinace a nic. Když použiju jako zem pin 3, výsledky nedávají moc smysl.
Vstup je podle mě pin 5, ale nepodařilo se mi ani při simple signalizaci UPS vypnout - signál vypnutí se totiž u různých výrobců liší, zkoušel jsem kladné/záporné dlouhé/krátké signály a nic. Je to divný. Kdybych měl odprásklý rozhraní, tak by podle mě nefungovalo ani simple rozhraní.
Vím, že například Powerware UPS mají duální rozhraní, default je simple a smart se startuje určitou sekvencí na vstup, po které se rozsvítí na UPS kontrolka komunikace s PC, která pak při vlastní komunikaci poblikává, nicméně tady už mi docházejí nápady ...
Sehnal jsem firmu, která v ČR tyhle UPSky prodávala a ty mi tvrdili, že se k ní musela dokoupit krabička s nějakou elektronikou pro komunikaci (30 USD), ale nějak si nedovedu představit, jak by to mělo fungovat, Chloride mi zase tvrdí, že stačí kabel a že zapojení podle toho schemátka musí fungovat.
Nejlepší by asi skutečně bylo, kdyby se našel někdo, se stejnou/podobnou (Aladin, Lan Start) UPS, komu to funguje, aby bylo s čím srovnávat ...
Takže finále - mám asi nějak řachlé to rozhraní.
Sehnal jsem člověka se stejným problémem (UPS bez kabelu a softu) a jemu kabel podle toho obrázku fungoval.
Takže pro případ, kdyby někdo řešil tento problém, ještě sem dám schemátka smart i simple kabelu, přímo od Chloride:
"ADVANCED Communication Cable - CA-1CB1S-03"
RJ22 - DB9F
2 TX 2
4 RX 3
3 SG 5
"BASIC Communications Cable - CA-1CB2S-03"
RJ22 - DB9F
1 1 Low Battery
2 8 On Battery
3 5 Signal Ground
4 4 Remote Shutoff
Soft je možno po registraci (je potřeba sériové číslo UPS) bezplatně stáhnout tady: http://connectivity.chloridepower.com/mopexpress
Třeba to někomu pomůže ...
Tak jsem se k tomu ještě jednou po mnoha letech vrátil, protože jsem narazil na "Technical manual" k UPSce.
Pravdu měl český prodejce - je k tomu potřeba další krabičku a Rainbow si správně všiml, že úrovně jsou TTL.
Piny (na UPS) jsou:
1 +5 V @ 20mA
2 Battery Low
3 Mains Failure
4 Ground
5 RDX ( Receives data from a PC )
6 TDX ( Transmits data to a PC )
Z krabičky vedou dva čtyřpiny, které už mají RS232 úrovně signálu:
1 Reserved ( +5V @. 10mA )
2 TDX, ( Transmits data to the PC )
3 Ground
4 RDX, ( Receives data from the PC )
1 Battery Low
2 Mains Failure
3 Ground
4 -----------------
Takže jsem zakoupil převodník TTL-RS232, zapojil (pin 1 jsou použil pro napájené převodníku) a konečně to funguje :-)
Snad mě nebude nikdo peskovat za necroposting ...