Takze ako idem na to ja detailne.
Vlozim do mechaniky CD po chvili vybehne ponuka, stlacim "a" zaskrtnu sa vsetky moznosti a potom stlacim "i" install
mikrotik sa nainstaluje a enterom dam reboot (CD s mechaniky vytiahnem)
Nabootju s HDD zadam admin, heslo prazdne a enter a som v konzole. Napisem setup a mam ponuku.
+ pred ponukou znamena, ze je to uz nakonfigurovane.
Potom musim este nastavit IP a gateway. Napisem 192.168.1.0/24
gateway prideli automaticky a rozsah pre DHCP tiez. Potom ma to pyta DNS, co mam zadat tam,
ved DNS mi prideluje ISP a nieje stale rovnaka.
V PC za routerom zadam do prehliadaca http://192.168.1.0, vyplnim login OK a som vo web rozhrani
idem na pppoe zapnem to a vyplnim meno a heslo a interface nastavim na ether2
idem na interface (mam tam 2x sietovka ether1 a ether2) ether1 je co ide s PC na ktorom je
mikrotik do switcha (zo switcha idu dalej ostatne PC v sieti) a ethernet2 je sietovka co ide
do HW routera ASUS (Asus je nastaveny v mode bridge) Na tej ether2 dam zapnut a vyberem moznost
aby IP priradilo automaticky (mal by pridelit ISP co je u mna T-Com) a nic sa nedeje, adresu neprideli
Co robim zle, alebo ako to mam nastavit, tu je schema ako to mam vsetko zapojene http://jany.ic.cz/schema2.jpg
tu je akysi vypis s konzoly
Trying 0.0.0.0...
Connected to 0.0.0.0.
Escape character is '^]'.
MikroTik v2.9.27
Login: admin
Password:
MMM MMM KKK TTTTTTTTTTT KKK
MMMM MMMM KKK TTTTTTTTTTT KKK
MMM MMMM MMM III KKK KKK RRRRRR OOOOOO TTT III KKK KKK
MMM MM MMM III KKKKK RRR RRR OOO OOO TTT III KKKKK
MMM MMM III KKK KKK RRRRRR OOO OOO TTT III KKK KKK
MMM MMM III KKK KKK RRR RRR OOOOOO TTT III KKK KKK
MikroTik RouterOS 2.9.27 (c) 1999-2006 www.routerclub.com
Terminal unknown detected, using single line input mode
[admin@MikroTik] > setup
Setup uses Safe Mode. It means that all changes that are made during setup
are reverted in case of error, or if Ctrl-C is used to abort setup. To keep
changes exit setup using the 'x' key.
[Safe Mode taken]
Choose options by pressing one of the letters in the left column, before
dash. Pressing 'x' will exit current menu, pressing Enter key will select the
entry that is marked by an '*'. You can abort setup at any time by pressing
Ctrl-C.
Entries marked by '+' are already configured.
Entries marked by '-' cannot be used yet.
Entries marked by 'X' cannot be used without installing additional packages.
r - reset all router configuration
+ l - load interface driver
+ a - configure ip address and gateway
+ d - setup dhcp client
* s - setup dhcp server
+ p - setup pppoe client
t - setup pptp client
x - exit menu
your choice [press Enter to setup dhcp server]: s
dhcp server interface: ether1
dhcp address space: 192.168.1.0/24
gateway for dhcp network: 192.168.1.254
addresses to give out: 192.168.1.1-192.168.1.253
dns servers: