Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Zdravím.
Zapojil jsem do PATA IDE Maxtor 250GB 7200 16MB. Bios i Win ho vidí, velikost udává 233GB, jen jakákoliv instalace se vždy sekne a vůbec nepokračuje dále a vše strašně dlouho najednou trvá...koukal jsem na stav a výkon procesoru s pamětí během operací a při běžné instalaci programu je vytížen kolísavě v rozmezí 20 - 100%, což mě přijde hodně a stránkovací soubor se zvětší na 421MB...Jinak disk slouží pro ukládání dat, systém mám na druhém disku Maxtor 15 GB 5400 ot...Nevíte co je špatně??? Díky
Základní deska: MSI PM8M-V
RAM: 768 MB
Maxtor 15GB - Primary Master
Maxtor 250GB - Secondary Master
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
peta303
DMA?
Zdarec. Tak v Biosu je DMA nastaveno na Auto.
Nemůže mít vliv v Biosu nastavení položky LBA/Large: Auto?? Nastavit to na LBA!?
V HD Tune mám toto:
HDD: Maxtor 250GB
Supported: UDMA Mode 6
Active: UDMA Mode 2
HDD: Maxtor 15GB
Supported: UDMA Mode 4
Active: UDMA Mode 2
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
V BIOSu se DMA nenastavuje, ale nastavuje se režim adresace. Nechej AUTO nebo LBA.
Do kterých konektorů na kabelu máš zapojené disky a do kterých konektorů na desce je/jsou zapojen(y) kabel(y)?
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Paolo
V BIOSu se DMA nenastavuje, ale nastavuje se režim adresace. Nechej AUTO nebo LBA.
Do kterých konektorů na kabelu máš zapojené disky a do kterých konektorů na desce je/jsou zapojen(y) kabel(y)?
OK...
Obrázek desky: http://images.tigerdirect.com/itemDe...36-out2-hl.jpg
Disky jsou zapojeny na JEDEN ATA 133 IDE Kabel zakončený v modrém headru (pravděpodobně IDE 0). Mě napadlo, jestli neni špatně to, že koncovka kabelu je v prvním disku a "slave" koncovka uprostřed kabelu je v druhém disku, přičemž oba disky jsou vedeny jako MASTER...
takto to mám: http://www.kids-online.net/learn/cli...ils/idecab.gif
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Odkaz na obrázek hlásí:
Kód:
403 Error
Access Forbidden to this Area
Oba disky nesmí být nastavené jako MASTER, ale měly by být nastavené jako CS (CABLE SELECT).
Osobně doporučuji použít dva kabely, protože jeden disk má max. UDMA 4 a druhý UDMA 6.
Máš CD-ROM zapojené taky na IDE? (v druhém konektoru)
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Paolo
Odkaz na obrázek hlásí:
Kód:
403 Error
Access Forbidden to this Area
Oba disky nesmí být nastavené jako MASTER, ale měly by být nastavené jako CS (CABLE SELECT).
Osobně doporučuji použít dva kabely, protože jeden disk má max. UDMA 4 a druhý UDMA 6.
Máš CD-ROM zapojené taky na IDE? (v druhém konektoru)
Obrázek desky: http://images.tigerdirect.com/itemDe...36-out2-hl.jpg
Zkusím to...
Mám jen DVD ROM a ten je zapojen do SATA 1.
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Jak píše Paolo, buď disky jako Cable Select nebo napevno Master + Slave. Pokud jsou dva jako Master, vznikají dost velké problémy.
DMA režimy se nastavují ve Správci zařízení ve Windows.
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
peta303
Jak píše Paolo, buď disky jako Cable Select nebo napevno Master + Slave. Pokud jsou dva jako Master, vznikají dost velké problémy.
DMA režimy se nastavují ve Správci zařízení ve Windows.
Jedná se o tyto disky:
http://techno-st.net/2007/03/20/images/IMG_0414.JPG
http://yoshino.sakura.tv/rakuten/7l250r0_1.jpg
Mno ono jde o to, že ani jeden z disků nenabízí nastavení SLAVE, jinak bych je hned nastavil. Na výběr mám pouze CS Enabled, Single (Master) a Slave Off. Takže je hodim na kabel a uvidim, zda pošlapou v pohodě...ale zatím kupodivu záhadně jedou, neb jsem po instalaci počítač úplně vypnul z proudu a druhej den nahodil a šli v poho, už se nic neseká...ale spíš se bojim, aby to nebylo jen na chvilku...
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Ale ale, oba disky nabízí režim slave, to, že jsi nepochopil, jak to pánové z Maxtoru mysleli, je věc druhá.
Starý Maxtor má jumper (dle obrázku J50) - když tam jumper je, tak je to MASTER (nebo sám na kabelu - SINGLE), když tam jumper není, tak je to SLAVE.
U toho novějšího je poloh pro jeden jumper víc - buď je v pozici CABLE SELECT (čili výběr zda MASTER nebo SLAVE si zjistí z konektoru na 80 žilovém kabelu) nebo MASTER (stejné jako výše) a SLAVE.
Osobně bych doporučil na jeden kabel dát jako MASTER ten starý disk (když se z něj startuje systém, tak musí zůstat na tom kabelu, kde je teď) a k němu jako SLAVE tu CD-ROMku. Na druhý pak na krajní konektor dal ten nový disk.
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Paolo
Ale ale, oba disky nabízí režim slave, to, že jsi nepochopil, jak to pánové z Maxtoru mysleli, je věc druhá.
Starý Maxtor má jumper (dle obrázku J50) - když tam jumper je, tak je to MASTER (nebo sám na kabelu - SINGLE), když tam jumper není, tak je to SLAVE.
U toho novějšího je poloh pro jeden jumper víc - buď je v pozici CABLE SELECT (čili výběr zda MASTER nebo SLAVE si zjistí z konektoru na 80 žilovém kabelu) nebo MASTER (stejné jako výše) a SLAVE.
Osobně bych doporučil na jeden kabel dát jako MASTER ten starý disk (když se z něj startuje systém, tak musí zůstat na tom kabelu, kde je teď) a k němu jako SLAVE tu CD-ROMku. Na druhý pak na krajní konektor dal ten nový disk.
AHa:mweheh: Ok, zkusím jak říkáš a dám vědět jak to dopadlo...=D
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Koty45
AHa:mweheh: Ok, zkusím jak říkáš a dám vědět jak to dopadlo...=D
Mno, tak jsem odpojil 250ku a dal jí na samostatný kabel a výsledek je, že 250ka je ted Primary Master a 15ka dokonce Secondary Slave =D To je v prd...=D
Sice už se to nezasekává, ale zato win startuje o hodně pomaleji. Tak bud to to vidim na novou instalaci win a nebo 15ka jde pomalounku do haje...=/ A nebo aktualizace ovladacu pro desku a radice...
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
To je tím, že máš CD-ROMku na konci kabelu a dělá MASTER pro ten disk.
Otoč pořadí disku a CDčka a bude to lepší.
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Paolo
To je tím, že máš CD-ROMku na konci kabelu a dělá MASTER pro ten disk.
Otoč pořadí disku a CDčka a bude to lepší.
Mno ale já mám DVD Romku =P a ta je na SATA kabelu, má to nějaký vliv??
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Koty45
Mno ale já mám DVD Romku =P a ta je na SATA kabelu, má to nějaký vliv??
Nevím, co myslíš tím =P.
Mám tomu rozumět tak, že máš na každém IDE kabelu jen jeden disk a nic víc?
Pokud ano, tak to chce oba zapojit na konec kabelu (černý konektor). Modrý (druhý konec kabelu) je zapojený v základní desce a šedý (uprostřed) nezapojen.
U 15GB disku pak zasuň jumper do pozice J80 (označení MASTER/SINGLE).
Re: Nový HDD - Po jeho instalaci se zasekávají veškeré operace ve WIN!
Citace:
Původně odeslal
Paolo
Nevím, co myslíš tím =P.
Mám tomu rozumět tak, že máš na každém IDE kabelu jen jeden disk a nic víc?
Pokud ano, tak to chce oba zapojit na konec kabelu (černý konektor). Modrý (druhý konec kabelu) je zapojený v základní desce a šedý (uprostřed) nezapojen.
U 15GB disku pak zasuň jumper do pozice J80 (označení MASTER/SINGLE).
Jop, přesně tak =) Už jsem tak učinil a fachá to v pohodě =) Thanks za vše jako vždy =)