-
komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Zdravím,
tak jsem se rozhodl, při cenách mini-ITX casů, včetně porovnání zdrojů, že si udělám vlastní case podle libosti.
1) HW
deska: ASRock AD525PV3
ram: 2GB DDR3 (obyč. / nic extra)
hdd: 1TB WesternDigital (zbyl mi z NSA zařízení)
psu: Fortron 200W (80-BronzePlus)
fan: Akasa low-noise 80 (kuličkové ložisko)
2) plán / nákres
po několika hodinovém měření šuplerou :) abych nic nepřehlédl, jsem si zakreslil komplet hw díly do počítače a začal plánovat case.
Původně jsem chtěl mít case hubenější a vyšší, ale asi by pak byl nestabilní.
PSU jsem tedy otočil naležato a desku s Hdd umístil nad něj. Nakonec jsem zjistil, že takto se mi dovnitř vejde případně druhý HDD - kdyby bylo třeba.
Komplet plán najdete v PDF zde.
3) Výroba a montáž
plexi mi za 460,-Kč včetně DPH vyřezala firma MK-plexi sídlící v Modřanech. Veškeré vnitřní řezání bylo laserem, venkovní hrany frézou.
http://www.atreid.cz/img/server-plexi/7.jpg
Přesnost řezání = naprosto dokonalá, např větrák není teřba k desce uchytávat, drží natěsno sám ve výřezu.
http://www.atreid.cz/img/server-plexi/6.jpg
Samotné plexi jsem se rozhodl spojit k sobě hliníkovým L profilem o rozměrech 10 x 10 mm a síla profilu 1 mm.
Jediné vrtání bylo právě na spojení plexi desek a profilů. Což byla sice pakárna, ale povedlo se...
http://www.atreid.cz/img/server-plexi/5.jpg
Současný stav:
Case je sestaven ze všech stran, uvnitř chybí dělící (7.) deska, na které bude držet Hdd a zákl.deska. Zítra ještě přidělám PowerOn tlačítko (microspínač), které bude vedle USB portů v připravené díře (původně zde měl být i reset, ale zdá se mi zbytečný).
http://www.atreid.cz/img/server-plexi/4.jpg
Složený CASE:
http://www.atreid.cz/img/server-plexi/1.jpg
http://www.atreid.cz/img/server-plexi/2.jpg
http://www.atreid.cz/img/server-plexi/3.jpg
Zítra pokračování....
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Citace:
Původně odeslal
Fox!MURDER
To se mi libi! :-)
Díky, dneska jsem konečně dodělal to hlavní - tlačítko Power ON
http://www.atreid.cz/img/server-plexi/8.jpg http://www.atreid.cz/img/server-plexi/9.jpg http://www.atreid.cz/img/server-plexi/10.jpg
Klínek s microspínačem přijde do předvrtané díry vedle USB portů, a bude napevno přivrtán do spodní části kejsu...
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Pokračování ze včerejška...
start tlačítko přišroubováno - viz obr.
http://www.atreid.cz/img/server-plexi/12.jpg a http://www.atreid.cz/img/server-plexi/18.jpg
A jdeme sestavovat díly včetně HW prvků...
musím říct, že se snadno kreslí / plánuje, ale samotná montáž k sobě je pakárna - kabely od zdroje Vám pak přijdou jak živý a úplně neohebný a všude se motaj !
Nakonec se ale povedlo... - pohled ze všech stran
http://www.atreid.cz/img/server-plexi/13.jpg http://www.atreid.cz/img/server-plexi/14.jpg http://www.atreid.cz/img/server-plexi/15.jpg http://www.atreid.cz/img/server-plexi/16.jpg http://www.atreid.cz/img/server-plexi/11.jpg
Zároveň s tlačítkem power jsem vyvedl i kabely na PowerLED a HDD-LED - viz obr.
http://www.atreid.cz/img/server-plexi/17.jpg
Takže když je vypnuto a rosvícené světlo vypadá hotové dílo takto:
http://www.atreid.cz/img/server-plexi/19.jpg
A v noci pak při spuštěném stavu:
http://www.atreid.cz/img/server-plexi/20.jpg
(HDD led svítí (teda když hdd maká) ve spodní části té modré kolmice (zeleně))
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Na kolik se ohriva ten disk?
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Citace:
Původně odeslal
NeMeM9aA
Na kolik se ohriva ten disk?
Mám to spuštěné asi tak 2h, a zatím jsem tam nic nekopíroval... čili disk v podstatě nic nedělá (zatím).
Ale jinak je v plánu pouze www aplikace, tzn. ftp apod. čili disk se bude "točit" maximálně rychlostí stahování... (bo uploadu).
Dále pak přehrávání filmů, musiky přes LAN = to taky není žádnej mazec.
Jediné co by mohlo disk krapet zahřát je kopírování dat tam nebo zpět na velkej comp... Ale to zatím neproběhlo. Takže zatím ti teplotu nepovím :)
ADD: Dle SPEEDtestu má Core 40°C a HDD 43°C, při tom "nicnedělání" -
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
tak pri intenzivni praci by to asi lezlo nekam, kam by nemelo. Na druhou stranu pokud se to bude stavat vyjimecne tak to nebude nijaky vazny problem.
Jinak samozrejme taky musim pochvalit. Pekna case.
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Vzhledem k použití myslím hodně luxusní case :) Nebude potřeba nějaký filtr/síťka na ten větrák?
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Pěkná práce, jsi šikula :-)
Akorát na ty kablíky ze zdroje bych doporučil dát nějaké flexi, když je to v průhledné bedně, takhle to IMHO trošku kazí celkový efekt.
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Kluku ty jsi ale šikovnej!
Nelíbí se mi to svícení, je to rušivé - na diskové úložiště, které má běžet 24/7, je to nevhodné.
Taky mi přijde zbytečné použití velkého zdroje - na tohle by bohatě stačil PicoPSU, mohl jsi ušetřit hodně rozměrů.
Jinak prácička dost dobrá, respekt!
Ta montáž stěn na hranoly v rohu je přesně to, k čemu jsem se u té své potvory chtěl dopracovat, ale zatím "nebyl čas" to dokončit ;D Už to mám na aktivním task listu asi tak dva týdny, že dodělám zadní stěnu...
eh, teď koukám, že to nejsou plexi hranoly ale kovové vinglíky - taky varianta :)
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Teplota: čoveče NeMeM9aA tak při včerejším kopírování asi 50GB na disk se hdd roztopil ze 43 na 46°C víc ne e...
Větrák - síťka - kryt - původně jsem něco chtěl falcone, ale pak jsem si řekl, že na to prdím, nikdo tam hrabat nebude, a kdyby náhodou někdo jo tak aspoň dostane přes prsty :)
Kabely od PSU - máš pravdu meteore bylo by to hezčí, ale asi bych to nenarval dovnitř. Musím říct že ten 24pin kabel do zákl.desky byl POROD tam nějak ztočit, byl jak živej a šíleně mě sral. Nakonec jsem u něj přestřihl i stahovací pásku která těch 24 kabelů držela pohromadě. Aby byl kabel více ohebnější....
Světlo Marty přiznám se, že původní NAS od Zyxelu svítil jak přetrženej a sralo mě to a teď si vyrobim takovejhle světlomet :)))
Nadruhou stranu, u Zyxelu svítile ledka přímo z šasí ven, kdežto tady svítí do boku plexi a ve finále to nešajnuje tolik, ikdyž plocha světla je daleko větší... No ale nebudu si hanit práci že :)))
Zdroj: Marty musím ti říct, že sehnat zdroj byl problém. Alza je úplně v prdeli, tam v tomhle případě nemají NIC ! A vůbec velký krámy jsou na malé psu problém... Nakonec jsem sehnal tenhle fortron, který je o rozměrech kolem 116 x 100 x 60 mm (cca) ale hlavně s údajem 80-BronzePlus čili nežere tolik, když není zatížen. A cenově za 420,-
Pokud jsem někde viděl vyloženě mini-psu tak cenově kolem 1500,- a to je moc...
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Dobrá práce Atreide, strojníkovo (nebo strojařovo? :D ) srdce plesá:)
Marty: to že se tobě to podsvícení nelíbí, přeci nemusí nutně znamenat, že je nevhodné - apropos, kdyby ho tam Atreid nechtěl, nebude tam...
edit: Dostupné mini-zdroje jsou problém obecně, takže se nedivím, že to dopadlo takhle. Navíc mi přijde Pico-PSU dost drahý oproti klasickýmu zdroji.
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
v mém případě strojařovo srdce (ikdyž teda, my byli první /a poslední/ ročník co nebyli pouze S (strojaři), ale SE strojař-elektrotechnik. Takže takovej half-und-half zmetek.)
Nicméně aspoň jsem si něco zapamatoval...
-
1 Příloh-a(y)
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Klobouk dolů! Hlavně ta preciznost měření mě dostává :idea:
Já se také přikláním na stranu pico-hafana, vyšel mě na 800Kč z ebaye, vč. adapteru. To je, myslím, slušné :)
Jak je na tom hlučnost? Je tam jen jeden větrník v bočnici nebo je i něco malého ve zdroji?
Můj case vycházející z Martyho specifikace...
Příloha 9135
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Citace:
Původně odeslal
Jakubisko
Klobouk dolů! Hlavně ta preciznost měření mě dostává :idea:
Děkuji, ten tvuj model (respektive zavěšení disků) jsem viděl u Martyho, a uznávám že takovejhle zdroj by byl asi lepší = méně výkonej, ale už je pozdě :)
FANs boční 80mm (otáčky cca 900-1100) a pak 60mm ve zdroji - hluk ale není...
BTW ty to máš lepené ?
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
5-ti stěn napevno z výroby a zadnice vteřiňákem. Mám taky 80W a tuhle jsem kamarádovi kupoval 120W, ten si stavěl trochu větší NAS :D
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Doktore, neříkám, že se mi nelíbí - Jen, že to je rušivé, a tedy z mého pohledu pro 24/7 provoz nevhodné. Ona totiž jedna malá pitomá modrá LED dokáže osvítit celej pokoj. Ale je to věc vkusu, každý nechť to má, jak chce - sděloval jsem jen svůj názor, od toho tu přece jsme.
Ad lepení, je to fajne, jen se s tím pak už nedá hejbat - nehledě na to, že lepený spoj nemusí být dokonale estetický (uvnitř mohou zůstat bublinky z lepidla). Tohle vypadá perfektně. Jen to zas může nasávat na hranách falešnej vzduch, pokud tam máš nějak extrémně řešený proudění; to ale není případ tohoto kejsu, kde je jaksi ten fan tak nějak "na hulváta" ...
Já se fakt musím dokopat k dodělání té zadní stěny. Chci do toho zabudovat taky větráky, ty teploty jsou u mě extrémní (mám to komplet pasivní). Zároveň chci přepracovat uložení disků - stávající řešení "na provázcích" je sice antivibrační, ale nevhodné z více důvodů (prověšuje se, obtížný transport, nelze fixovat, odvod tepla, proudění vzduchu...).
Každopádně, Atreide, paráda. Moc pěkná práce.
EDIT.
ad ceny zdrojů -
1. PicoPSU bez adaptéru v přepočtu za 440 kč včetně dopravy,
2. nejlevnější malej zdroj z alzáče za 431 kč
Takže si myslím, že to tak žhavé není - při úspoře elektriky a rozměrů, tepla a hluku? A 12V adaptér se sežene za pár korun, pokud se neválí někde doma v koutě :)
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Citace:
Původně odeslal
Marty
1) Na picoPSU jsem narazil, ale nějak jsem z fotek pochopil že to je předělávka na 12V do zapalovače do AUTA (pokud někdo chce PC do vozidla)
2) add 2 EUROCASE (viz alza) - mám o něco kratší Fortron 200W který má parametr 80BronzePlus - tzn že bude žrát o DOST méně než ten EC který jsi postnul... ten 80+ nemá a ještě to je 250W.
-
Re: komplet PLEXI case na integrovaný Intel Atom, HDD a malé PSU.
Jasně, v pohodě, to byla spíš reakce na Doktora, že jsou PicoPSU drahé oproti klasickýmu zdroji.
Ano, původně zřejmě byly určené do auta - některé mají širší spektrum napětí na vstupu, můj má např. 12-36V. O to víc jsou s výhodou použitelný doma pro tyto účely :)